... PCBExpress can't do this directly, they add a grey background and dots to the printout to prevent it. You can futz with the image and remove this but it's...
... printer, ... dots ... remove ... (most ... klunky ... Anthony is correct. Express only offers a simple output and even if you bring it into PAINT and...
Hi All, From what I have seen, there are a few free versions of software for the hobbiest to do schematic layout, board layout, autorouting and then Gerber...
Look at RIMU http://www.hutson.co.nz/rimupcb.htm $65.00 unlimited no auto router but good also Pclogic It does auto router no limit also has a lite ver very...
5501
Homebrew_PCBs@yahoogr...
May 1, 2004 2:38 pm
Monthly Reminder, please read: Subject lines: Remember to change the subject line if you are straying from the original thread. Please change the subject line...
I saw some CEM-1 on e-bay and couldn't find out a whole lot about it. Since I will be etching traces with a mechanical router, I'm curous if there are any...
On Sat, 01 May 2004 16:28:08 -0000, Dave Mucha <dave_mucha@...> ... cem1 is cool, but i don't recomend milling. Look in the group links -> design rules...
I think Eagle is great. Libraries are easy to extend and modify. Autorouter helps a lot. I like that I can write C like programs to do neat stuff with it, such...
Hello, What is the min trace width while using a transfer product liek press and peel blue? I want to use SSOP parts and these have pads that are 0.38 mm wide...
re. negative images - If you can output gerbers, you can get almost any manipulation of the impage you want via the various gerber utils. I wouldn't bother...
... I plan to add these, and any more that I come across from the readers. Currently Olimex offers a list of a few dozen packages, but no information about...
"least number of ... Musta done 3 ... NO ... least a ... I would tend to think around 10-100 times that, and yes, I've seen those too. Really cool, but I don't...
... The student version is free... however its limited to the number of parts, and I don't think you get the autorouter. At least it used to be that way. Ron...
... Look in Files: http://groups.yahoo.com/group/Homebrew_PCBs/files/Toner_Transfer/ A couple photos of someone's 8 mil traces with 8 mil spacing, and that was...
HP LJIIID and ALL the error comes from it (rough edge). The added error of the transfer is much lower than the bad quality of the printout. It seems to be the...
... of the ... I found in the few TT boards I have ever made, was that the dusting all over the board were undercut by the acid so fast that they never posed...
... Seems so.. ... this is always a problem with laser printers/copiers. But i think the older the printer and the thicker the paper the worse it gets. I can't...
Hi all, I have a board that I want to put a chip socket into. But, and here's the problem, I want to solder the body of the socket, not the pins. The body has...
What size (wattage) iron are you using and what kind of tip? Jay Beckham Berkeley Springs, WV NEW WEB SITE: http://www.south-shore-line.com ... From: Dave...
In a message dated 5/2/2004 10:24:20 PM Central Standard Time, jbeckham1@... writes: What size (wattage) iron are you using and what kind of tip? For...
On Sun, 02 May 2004 23:19:23 -0000, Dave Mucha <dave_mucha@...> ... You can buy "single socket pins" or you can simply break them out of a old pc cpu...
... the ... guess ... mill ... advantage. ... they ... told. ... into big ... I have both styles and when doing 140 pins, or 6 strips, the strips are much...
