Just so everyone knows, heavy-duty power conversion is done with three phase loads 120 degrees apart just to solve this problem, which exists for ordinary...
Dear Friends, Scholarships info for your study, all international eligible check the list here: http://www.wisely-online.com/scholarships.htm Have a nice day...
I wouldn't trust this. Gabung has been removed from the group. Simon Gabung Karina <gabung.karina@...> wrote: Dear Friends, Scholarships info for your...
Good! I've been busy studying the ARM processor and designing a pressure transducer/CAN bus interface for the vacuum control system. I did manage to get an...
In some other threads, the question of using permanent magnets for polywell construction has been raised occasionally. This was often shot down by raising...
Regarding the cusps issue, the cusps produced by using permanent magnets would occur in exactly the same location as the cusps produced by an air coil based...
The problem with permanent magnets is that field lines and therefore electron flows intersect the surface of a permanent magnet but do not need to intersect...
... magnet ... over the magnet. It has a big hole where one of the cusps exists. For the magnets you suggest there would be a lot of SmCo at one of the cusps....
There's another big problem with permanent magnet disks. They surround the fusion reaction in most directions, and will be hit by the bulk of the radiation...
Dick is correct. For all permanent magnets the field lines must intersect the surface. Dr. Bussard did toy with some designs that used permanent magnets but...
... by ... to ... heat ... absorber ... a ... I was considering the Hydrogen-Boron based direct electricity generating approach rather than a heat engine. I...
... can ... I think that's where I was headed in my amateurish, neophyte, ignorant manner, namely towards a design that doesn't require recirculation... ...
I am thinking of using permanents magnets as well, for experimentation. The electron losses trough the cusps is high, and would not allows a net energy machine...
... by ... I think that I may need to further clarify the description of the magnets that I was considering... I was thinking of relatively long, skinny, rod...
... recirculation ... ignorant ... recirculation... ... go ... and ... recirculation? ... Duh, I am an idiot. Positive charges on the magnets won't work at ...
... magnets ... create ... a ... reduction ... If ... a ... comments. ... but ... from ... The problem with the MagGrid intercepting alpha particles is that...
... I'm not sure what you mean. It is my understanding the a positive charge on the MagGrid is absolutely essential. When electrons escape throught the cusps,...
If this goes forward a lot more people are going to have to understand how it works. Every repeat of an old question sharpens the argument and reduces the...
I was attempting to come up with an electromagnetic coil design that could be useful for experimentation. To help assist with the design process, I used the...
I didn't do a detailed examination of your spreadsheet so this reply is at a higher level. In general if you are trying to relate WB-6 (a current pulsed...
Ok, I've spent the last several hours searching the web for a definitive equation that simply relates the magnetic flux surrounding a wire to a steady state...
... reply is ... machine) ... flow ... Probably ... is ... design ... I understand that WB-6 is pulsed, and that the instantaneous current, power, and...
... wrote: <snip> ... current, ... I ... using ... (whether ... my ... I ... the ... to ... conversion ... Ok, so Devlin was kind enough to point me to...
The government is too cheap to spend money on sperconductiing magnets. The recently closed the stellarator porgem. How much many was wasted ont that? Thye...
... that ... design ... and ... layer ... in ... 30 ... kw ... the ... After further research using other various solenoid equations that I finally located...
Welcome to the world of complexity. Yes, copper wound toroids are poor magnetic field generators. Is this important? Depends of what you believe was going...
Kevin, I did not check all the equations, but the results seem on the right order of magnitude for a copper coil. For a specific coil size, the power required...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
