I was just wondering if someone could confirm what the best ink color would be when using an Epson R280. It seems as though most everybody has had success...
614
alienrelics
Dec 2, 2010 2:58 pm
It should be exactly the same color(s), it is the ink, not the printer. The printer is just an ink delivery system. Steve Greenfield AE7HD...
615
barry
bazzapromenade
Dec 11, 2010 5:51 pm
Hi guys. I am new to this forum and I have a couple of questions. I have an Epsom r2400 printer that I am going to use. It will take boards up to 13 inches...
616
handy2209
Dec 12, 2010 8:23 am
Sorry I can not comment on the ink problem but other aspects of the email caught my attention. I became very interested when I saw the mention of the printer...
617
barry
bazzapromenade
Dec 12, 2010 3:43 pm
I am currently using 1/16 board.I made a carrier from a for sale sign and a sheet of the colored plastic card that is kept right next to the for sale signs at...
618
muhammad rizqi
muh_rizqi
Dec 16, 2010 6:37 am
Hi All This is my first direct print to PCB http://www.youtube.com/watch?v=vFjDArXbzgM rizqi [Non-text portions of this message have been removed]...
619
Andrewdavid.mathison
andrew.mathison
Dec 16, 2010 2:19 pm
Hi muhammad rizqi shame you cut the video off without showing a quality image of the PCB at the end.....can you post a clear picture on the blog? Greetings...
620
ogre@...
erg0gre
Dec 17, 2010 11:07 am
Hi, take a look at http://www.refillbros.com/en/manuals/p1697-epson-stylus-c58-c78-c92-d78-d92-s20-t10-t20-service-manual Regards Michael...
621
Ingo
i.schuldes
Dec 17, 2010 5:20 pm
I just uploaded some new photos of a testboard - it is a layer of an arduino mega design. It was done by direct inkjet printing of the etch mask....
622
Boman01
bertho_boman
Dec 17, 2010 5:31 pm
Congratulation: That is very impressive results! Can you please describe your setup? TIA Bertho From: Ingo Sent: Friday, December 17, 2010 12:20 I just...
623
flaretom
Dec 17, 2010 7:01 pm
Hi Ingo, Really impressive results! I'm currently trying to get acceptable results with my converted EPSON C84. What ink you're using? I know the MISPRO ink is...
624
mchristisen
Dec 18, 2010 1:45 pm
Any plans for where the group will move to if and when Yahoo closes Yahoo Groups?...
625
Andrewdavid.mathison
andrew.mathison
Dec 18, 2010 2:10 pm
That looks as good as perfect!!!! Well done and thanks for the Fotos. Greetings from Andy Mathison [Non-text portions of this message have been removed]...
626
samsagazzzz
Dec 18, 2010 7:16 pm
Is possible to Modify an Epson T24 or T25 or T33? Are the 3 models available on my city, i want to purchase a new one to make the PCB Printer!...
627
alienrelics
Dec 18, 2010 7:17 pm
I don't like Google groups layout. I might try making a forum on my site. I registered homebrewpcbs.com but haven't done anything with it yet. Steve Greenfield...
628
luis h
luisguillermo98
Dec 19, 2010 3:08 am
I am about to buy a couple for epson printers. I want to know what is the smallest width size have you guys able to get from these printers?. is it possible to...
629
jedavis1947
Dec 19, 2010 3:09 am
Beautiful work. Inkjet resist application has come a long way. I think the next problem to overcome is the thru holes. A solution for the PTH problem is...
630
alienrelics
Dec 19, 2010 2:23 pm
I don't recall who printed it, but the board on the homepage of the group has thin lines that start at 0.001 inch and work up from there. You can view it here...
631
Ingo
i.schuldes
Dec 19, 2010 4:51 pm
... I am very sure that the lines in these pictures are by far wider than 1 mil. Its no problem at all to define such a fine line in your graphic application,...
632
Ingo
i.schuldes
Dec 19, 2010 8:46 pm
... Thank you very much. As a printer I used a prototype of one of our A3 models, which are usually used for printing fontpanels, scales, signs etc. which have...
633
William Nelson
wnnelson0
Dec 19, 2010 9:32 pm
That is my photo of the etched PC board that is being referred to. You are correct that the line sizes are probably not the sizes that are shown on the board....
634
Ingo
i.schuldes
Dec 19, 2010 9:46 pm
... I had the same problem at the beginning. Was very happy with the first prints - until I started to measure the tracks with a microscope. That caused a lot...
635
Mark Lerman
mark_from_po...
Dec 20, 2010 6:31 pm
You need a stage micrometer to measure the true widths. Not expensive if you already have a microscope. Mark...
636
Ingo
i.schuldes
Dec 21, 2010 10:41 am
... I used a USB Microscope with a software-measurement tool for my photos in the photo sction....
637
Boman01
bertho_boman
Dec 21, 2010 2:09 pm
A free reasonably accurate alternative is a flatbed scanner if you happen to have one. As a test I scanned a PCB at 3200 optical ppi and I added a calibration ...
638
tecni_fireelectronics
tecni_fireel...
Dec 21, 2010 7:44 pm
I am trying to dip my board with, all through hole components mounted, in liquid solder but some traces and pads get shorted. I understand that solder mask...
639
alienrelics
Dec 21, 2010 7:51 pm
Look in Homebrew_PCBs in the Photos under the directory Roll Tinning Machine. David Hopkins, the maker, gives a description of it in this thread: ...
640
alberto albert
tecni_fireel...
Dec 21, 2010 9:24 pm
Thanks Steve. I just joined the group; well, I´m waiting for confirmation. To: Inkjet_PCB_Construction@yahoogroups.com From: alienrelics@... Date: Tue,...
641
Steve Greenfield
alienrelics
Dec 21, 2010 9:55 pm
Done. Steve Greenfield AE7HD http://www.linkedin.com/in/stevenjgreenfield...
642
John
ikkefestbrems1
Dec 31, 2010 7:26 pm
What is the best software to design pcb. It is not for comercial use. I'm currently using Eagle but would like to be make boards lager than 80x100mm....
