The system from Schuldes, the cost is higher as Mispro and instead of a preheat cycle a chemical primer is used. The resolution seems to be lower compared to...
I dont know with whom you had talked in the past...so lets give you a update: I cant compare the costs, as I dont know about the prices of the mispro inks. Yes...
New to all this so bare with me pse . Where can I buy this and is regular etch resist what folks are using to print on PCB's using an inkjet printer? What kind...
692
Inkjet_PCB_Constructi...
Feb 15, 2011 5:21 am
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the Inkjet_PCB_Construction group. File :...
693
Inkjet_PCB_Constructi...
Feb 15, 2011 5:23 am
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the Inkjet_PCB_Construction group. File :...
Hi, In the service manuals an adjustment program is mentioned. Can anybody upload this program? It would be very useful if one (e.g. me) is going to change the...
I'm about to start modifying my printer (R260), but I have a few questions that I haven't seen addressed: 1 - What is the optimum printhead to pcb distance? I...
Hi Roman, Great! It seams to be for the C64, but the few things i tested work fine with the C84 too. Maybe there is no diffence at all. Thank You very much, ...
OK, the C64-program didn't work for the EEProm and adjustment data. But now knowing what to look for, i found the correct file in the web. For completeness...
I have put together a tutorial describing my "hack" of the R260 (and similar) to print Mispro ink on PCBs. Full documentation and step by step directions are...
... ~$ host www.MarksData.com www.MarksData.com is an alias for MarksData.com. MarksData.com has address 173.201.0.1 MarksData.com mail is handled by 0...
It worked fine for me. Mark: It looks like a good start except the "Next" does not work or is not finished. Bertho From: Wayne Topa Sent: Thursday, February...
The target area for Next>> button (with a target of <http://www.marksdata.com/marksdata_003.htm>) seems to be about one pixel high located about 10 pixels...
... Since you aren't releasing the code for the uC, and are offering to sell it, this is an advertisement more than it is a hack or a tutorial. I don't mind...
Whooah! The code is available (click on the link), and I was considering selling a programmed chip for about $1.50 USD, basically to cover cost and postage. If...
He's not spamming us. Mark put a link to the code on page 1 (at least I looked at the code from a link on one of pages 1,2 or 3) and the rest of the...
Or for a text version that can be copied and pasted: <http://www.marksdata.com/R260.asm> Donald. -- *Plain Text* email -- it's an accessibility issue () no...
Okay, so now I have this modified R260 that can (in theory) print pcbs. Problems and questions: 1 - When I print on a pcb, I get bubbly looking traces that...
Well, I tried pre heating, and it worked very well. Have to see if pre etch then pre heat works better. Does the pre etch have to be done just before the...
Might want to take a peek at it using firefox - some overlapping text and alignment issues all over the place! Andrew ... [Non-text portions of this message...
... Mark, my sincere apologies for missing that link. I really do appreciate your sharing and I am sorry I was too quick to blame. Steve, I repeatedly said I...
Always clean -before- you sand. Any oils get into the sanding scratches and are then very difficult to get out. I think you are describing what painters call...
I have found that in order to get a good trace I have needed to reduce the ink % that is used. When viewed under magnification (old eyes) the printed ink is...
