On behalf of Lectrosonics, Inc., let me welcome you to the new LecNet2 user's group. Please post your questions, tips, system design ideas or suggestions here....
Just wanted to say hello to all new members. It's great to have this new group and I hope a lot of our customers find it useful! Regards, Howard Kaufman ...
Hi, my name is Andy Cross, and I work for a Design-Build contractor in upstate New York known as DCI Sound. My responsibilities include electrical design,...
Hi, We love LecNet 2 DMs. We have notices some instances of distorted audio when operating compressors or limiters with line level inputs. Inputs meter...
Hi Mark, I saw your posting last week, but was not able to respond until now. We have also noticed this distortion, and have contacted the factory about it....
Andy and Mark - Check the attack time on the compressors - I ran into the same thing at my church where we have the beta test unit - the units used to ship...
Gordon Moore
gordon@...
Oct 11, 2006 3:19 pm
10
Hi Gordon, Thanks for the tip. I usually set the attack a bit quicker than 20mS, but we will give that a try. Is there any thought as to why that particular...
Gordon: Having visited the "compressor noise issue", I need some insight into another matter. We often times have systems with two or three presets, often...
I have plenty of thoughts but my therapist taught how to ignore the really weird ones....... As far as the labels go, we have had a few reports like this but ...
Gordon Moore
gordon@...
Oct 12, 2006 6:15 pm
13
For those of you in Australia, NZ and surrounding areas, there will be a workshop on the LecNet 2 Series signal processors during the SMPTE show in Sydney in...
Is there any way to tell the master DM1624 to change the preset number on a slave DM1624 when a programmable input is used on the master to select the active...
Yes. One way would be to connect from logic outputs on the master to logic inputs on the slave. You'll need an input/output pair for each preset. Program...
Sorry, I didn't mean to mislead but what I said in my previous response about the logic going "high" can be confusing. I meant that set the output logic pins...
Howard, Ahhh....thank you. We had intended to connect LEDs to the Programmable outputs to let us know which preset was current. From what you are saying, I...
Yes! That is exactly what I was describing - minus the LED, which I didn't know you were looking for. But it should work as you understand it. Regards, ...
Hi all, my name is JR Tyler, I work for DCI Sound in upstate NY. Looking forward to sharing ideas and learning along the way. JR...
JR Tyler
jrtyler@...
Nov 20, 2007 6:33 pm
21
Hi JR, Just a quick welcome to the list. There isn't always a lot of activity here, but if you have any comments or questions we are happy to answer! Regards,...
Hello, I have a question concerning the back panel controls on a DM1624. Is this the right place to ask it? bob ________________________________ From:...
Thanks. I want to control one of the input channels on our DM1624 with an external pot. I found some instructions for a DM84 which I hope will suffice. But,...
Hi Bob, Sorry but your thinking is not correct here. The way the rear panel controls work is that they are attenuate (cut) only. They minimuam attenuation is...
Howard, I've got to leave right now, but, how about if I swap the ground and +5 connections to the pot. Then set the mike gain to just below the feedback...
Well, that would reverse the action of the pot, but it would work opposite of what you intend - full clockwise would be maximum attenuation. So I wouldn't do...
I've just taken over the maintenance and operations of our Church sound system. We have a LecNet 2 digital mixer. Is there a help location that will explain...
Hi Mark, I think the best way to proceed might be with a one-on-one phone conversation. If you like I can call you, or feel free to give me a call at: (516)...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
