Hi Bruce, I'm very happy with my Venue and 400 series system and would never like to exchange it for a 200 series. I think you got the wrong person here. To...
Tried to find some wiring info on the Sennheiser web site and in our files, but no luck. Try the wiring shown in the LM/IM transmitter manual on page 11: ...
I have a problem with my DMTH4. I have it connected to two other DM16/12. The mixer work fine whenever a phone call is not connected to the DMTH4, but...
Hi Justin. This group focuses on wireless equipment and issues. I will forward your message to our LecNet gurus for a reply. The other discussion group focuses...
I have just signed onto this group.My name is Brian Shennan.I have an SM transmitter and a 411A receiver along with a couple of old Lectro 185 systems that I...
Hi Brian. Welcome to the group and many thanks for offering to share your experience. This group is not super active, since we focus on technical and ...
Some of you may recall that my entire (uninsured) sound package was stolen last August. This morning 99% of that gear is spread out on my living room floor. ...
It,s the new year present. ... De: Lectro@yahoogroups.com <Lectro@yahoogroups.com> Para: Lectro@yahoogroups.com <Lectro@yahoogroups.com> Enviado: Thu Jan 11...
Mario Nazoa
mnazoa@...
Jan 12, 2007 1:47 am
1080
Hi A general question about if and when Lectro is planning on releasing a fully digital radio mic system. I'm looking at buying a big kit of the 250mW...
if they planning they wouldn't say it not to kill the current products Chris there is always people who buy before changing product , the only concern I think...
I mend digital out for the processing which already happens inside receiver digital domain ... From: Chris Bollard To: Lectro@yahoogroups.com Sent: Tuesday,...
I can understand your anxiety at making such a large investment in equipment, but there is a more important question: will the equipment you acquire serve your...
Senator Mike Michaels
Senator@...
Jan 16, 2007 2:57 pm
1084
Thanks everyone for your comments I guess what I'm looking for in a digital transmission system is the removal of IM problems that you get when running 12 to...
... From: "Chris Bollard" <chris_bollard@...> To: <Lectro@yahoogroups.com> Sent: Wednesday, January 17, 2007 3:37 AM Subject: [Lectro] Digital...
H. Cohen
henryc@...
Jan 17, 2007 2:18 pm
1086
I'm not sure that going to "all digital" transmission would be a panacea for the spectrum problem you fear... what with interference sources abounding, you...
Senator Mike Michaels
Senator@...
Jan 17, 2007 4:44 pm
1087
Hi everyone, I am trying to send a line-level signal into my UM190 transmitter (from my Sound Devices 302). I set it up the same as when I use a UM200C Tx....
Jason Porter
soundmixer@...
Jan 21, 2007 4:26 pm
1088
Hi Jason, The Line level wiring instructions in the manual show this: LINE LEVEL SIGNALS The normal hookup for line level signals is: Signal Hot to pin 5,...
Jason , did you try to attenuate the signal with 302 outs ( menu)? ... From: Jason Porter To: Lectro@yahoogroups.com Sent: Sunday, January 21, 2007 6:27 PM ...
Hi Oleg, Yes, if I lower the output on the 302 to -10db, it sounds fine. -Jason ... From: Oleg Kaizerman To: Lectro@yahoogroups.com Sent: Sunday, January 21,...
Jason Porter
soundmixer@...
Jan 21, 2007 5:48 pm
1091
Hi Ken, Yes, I have 2 line level cables that work perfectly with my UM200C's. I tried adding a 100 ohm resistor (actually, 160 was what I had) it sounds much...
Jason Porter
soundmixer@...
Jan 21, 2007 5:54 pm
1092
so work this way ,.give the tx + 8 db reference tone and calibrate the input so the second led would lit a bit calibrate your limits for something like +10 DB...
If you're wired as the instructions show and you only have a 160 Ohm resister in series with pin 5, you could try going up to a 1K Ohm or higher to gain more...
100K ohm... DOH! I just replaced the 100 ohm with a 100k ohm and all is well. Thanks to Ken and Oleg for helping me on this issue. Oleg, I owe you a Guiness!...
Jason Porter
soundmixer@...
Jan 21, 2007 11:12 pm
1095
I am working with 2 ucr411A and the the beltpack is a um400. I have notice a big difference in sound quality from my old ucr301(Europe version of the ucr200)....
There are quite a few different things that can cause hiss in a wireless system. The hybrid system is flat to 20 kHz, so you can hear high frequency noise from...
Joao, My 400 gear sounds better than my 200. I have SM transmitters, a 400 plug on, and use VRT's with Venue for receivers. I trust that all of the units are...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
