Hello, I just received my new VR Field but instead of two dipole antennas I got a couple of Coaxial BNC's. I'm somewhat disappointed since in the box I found...
Hi Bruce Jones, It's R400. Its S/N is 316. Its firmware version is 1.9. We have changed the different transmitter and receiver, but the problem also happened....
Thanks Nina. If the R400 has the same problem with two different transmitters, then the problem is the PLL in the receiver. A part needs to be changed in the...
Hi Sergio. Sorry for the misunderstanding. There are lots of different kinds of antennas that are used in different applications. We include the antennas that...
Thanks for the clarification Bruce. I also found in the box some kind of transparent flat plastic rods but couldn't find in the included documentation the...
Hi Sergio. The plastic straps included with the VR Field receiver are attached to the NP1 style battery to make it easier to remove the battery. Peel the...
Hello, I'm just back from my first gig using my new VRField and one thing that happened was that sometimes I was using only one transmitter out of four...
Hi Sergio. You can remove the module if you are not planning on using it. In fast-paced or critical production it might be a good idea to leave one in for...
... Hi Bruce, You must be kidding. Just unpacked my new VR Field (4 VRTs Block 27). Tested it. Very impressive Reach excellent. But to my shock no switching...
... Hi Sergio, The manual which came w/ my unit mentions the straps in the packing list (first page I think) Can´t really use them because my NP1´s are not...
I know "the management" will have the official responses soon, but to get rid of the flashing message, you can tune the RX that is causing it to another freq...
Senator Mike Michaels
Senator@...
Jun 11, 2007 3:22 pm
1177
sorry, I meant to combine responses: RF and antennae are a complex topic. antennae are the lengths they are for definitive reasons, based in physics. Larry is...
Senator Mike Michaels
Senator@...
Jun 11, 2007 3:31 pm
1178
i also don't see any point loose half amper when not using the receivers , especially for these of us who stay on relatively small batteries ( 6-12amp) it...
Tom and Sergio: The elements of the A-COAX BNC antenna are in the last 8 or 9 inches. The coaxial cable in between the elements and the BNC connector can be ...
Hi everybody. Sorry for the delay with this reply. Having problems with my Internet e-mail and cannot post a reply. Have to create a new message. Don't know...
Hi everybody. Sorry for the delay with this reply. Having problems with my Internet e-mail and cannot post a reply. Have to create a new message. Don't know...
My first reply to the questions about the coaxial BNC antenna posted at 12:55. I wrote it at about 10:00 AM this morning. Don't know where it was hiding. Yahoo...
I admit I wasn't paying attention to detail at NAB and didn't question anyone about the differences between the UM400 and the UM400A. What are the differences...
Sorry for the delay. My computer croaked again, but have e-mail temporarily. The UM400a has the servo bias input section like the SM series transmitters. This...
we have a UCR401,its s/n is 1178, B28 ,but now there have a questions with it.when we use it ,the distance for it its about 10 meters,the transmiter we have...
Short operating range can be caused by interference, bad or wrong antennas and connections, transmitter gain set much too low and combinations of all these...
Hi all, I would like to check whether is it possible to transmit from 1 transmitter (either SM or UM400) to 2 or more receivers (411 or 401)? Also what would...
Lawrence, There is no limit to the number of receivers you can have that are tuned to the carrier frequency of a single transmitter, as long as they are in...
Hi,bruce , Thank you for your answer.but I am sure our transmiters is well.because when we checked it ,we changed several transmiters ,and changed two UCR401...
Dear Bruce: Tks for your answer and analysis. We tested wireless performance based on signal channel, so, it shouldn¡¯t be caused by intereference. Can we...
I am using 200 series wireless mics with 400 digital mics recording on the sound devices 744. What is the delay in milli seconds between analoge and digital...
The delay in the 400 series is about 1.6ms per side, i.e. 1.6ms for the transmitter, and 1.6ms for the receiver. This gives a total of 3.2ms when using a 400...
sometimes electronic things stop working well and need to go to the hospital to be fixed! Senator Mike Michaels, c.a.s. Studio M Productions ...
Senator Mike Michaels
Senator@...
Jul 11, 2007 2:35 pm
1194
Thank you for trying different combinations. If the problem occurs with only one receiver using several different transmitters on various frequencies, and the...
For those of you in Australia, NZ and surrounding areas, there will be several interesting workshops at the SMPTE convention 17-20 July at the Sydney...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
