Allan: The UCR201 list price was $1525.00 when it was discontinued. Hope this helps with your decision. Sincerely, John Muldrow To: Lectro@yahoogroups.com ...
John Muldrow
john@...
Oct 1, 2007 2:22 pm
1327
I saw an UCR 205d complete kit on bblist.co.uk for £950.00 pretty expensive. for a second hand one if you think the exchange rate is 2 to the dollar is far...
http://www.coffeysound.com/product.php?productid=748&cat=45&page=2 Any one tested it with lectro , if so how does it work question to Bruce or any other...
Nice thought. Thanks Oleg. The UH transmitter has switching power supplies to produce 5 different voltages, a DSP, a microprocessor, a 100 mW RF power amp, and...
does the ut use polirized capsulres or electret elemnts ? ... From: brucejones87124 To: Lectro@yahoogroups.com Sent: Monday, October 08, 2007 6:50 PM Subject:...
Bruce I will more appreciate you will redesign the txs as um and lm and uh be able take small camcorder liion batteries on the side , its real drag to hook tx...
I see the new Lectro portable receiver was unveiled at AES - anyone got some information on it? When will it be released? Peter Kraan [Non-text portions of...
Hi Peter. We are hoping to have some production by the end of the year. So far, so good, but Murphy is out there plotting against us. We can only imagine what...
it is not a "stereo" RX, it is a dual RX package, in development, and was previously shown at NAB. It is being designed specifically for camcorders with RX...
Senator Mike Michaels
Senator@...
Oct 10, 2007 2:56 pm
1335
Dear Group. I've just received a brand new series of 6 beutifull SMa Tx. Following the instructions of lectro in the spread frquency I've achived in Lucca...
Dear Group what happen if I power up my VR venue receiver at 12 dc V. instead of the 15 dcV that was written on the power input soket? Someone of you have that...
Hi Maurizio. 12 VDC should be fine. What are the serial numbers on the main units? (not the receiver modules) ... V. instead of the 15 dcV ... down to 10 dcV....
Hello Everyone. I am using a UH400A Plug-on Transmitter and i am very delighted by the ease of use and sound quality. How ever i am using a wide range of...
the uh 400 doesn't work with some others as well like geffel 200 and shures do you working with regular 100 stage or with 400 .check both , the power supply's...
Hello Andreas, The issue with the KM100 series microphones is that when used unbalanced, they are actually pin 3 hot (but out of polarity). This information is...
hi Karl I tried it with the gefel , no luck maybe you can find one and find some nice solution for sms-200 body ... From: Karl Winkler To: Andreas Ruft ;...
Is this possible at all? I'd like to use 3 blocks of Lectro receivers in one rack and I have 1 UMC200d here. Probably wishful thinking, but thought I'd drop...
that's the reply I got from Larry F using the nearest block with lectro distributing system few months ago using 25/26 block distro with block 24 If you stay...
Set the out of band receiver as close to the UMC tuning range as you can and keep an eye on the RF level entering the receiver. Depending upon which receiver...
Hi, A new 400A-AA transmitter has gone down. When it's powered up it seems fine for 5 seconds, then both LEDs start flashing red and it stops working. Any...
Sorry you are having problems. Let's hope there is a quick fix. The UM400A runs on a 9 volt battery. The SM series models run on AA batteries. Need to know...
Hello to all, I have news eng gear including Lectrovoice CR187 & H187 packages used with ElectroVoice (EV) RE50 mics attached to the cube transmitter. Problem...
Kowald, James R
jim.kowald@...
Oct 24, 2007 5:08 pm
1350
Hi Jim. We use a standard Switchcraft connector on top of the plug on transmitter, so it should not cause any more wear than a cabled mic with the same...
Hi Stephen. The UM400a AU version (and other models as well) have a diagnostic error message when the PLL does not lock up. The mod level LEDs will flash soon...
I have a new 411a with a problem, when switched on the frequency screen flashes the frequency readout and I have no reception. After switching off and leaving...
The flashing frequency screen signals that the PLL did not lock up. Our service manager suggests the receiver make a quick trip to New Mexico. There may be...
Hey, If you have specific audio questions in the future, you might also try a new forum @ www.locationaudio.net . It's a forum designed for film and audio...
Hey, If you have specific audio questions in the future, you might also try a new forum @ www.locationaudio.net . It's a forum designed for film and audio...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
