Hey, If you have specific audio questions in the future, you might also try a new forum @ www.locationaudio.net . It's a forum designed for film and audio...
Hey, If you have specific audio questions in the future, you might also try a new forum @ www.locationaudio.net . It's a forum designed for film and audio...
Hi Vin, The LM only provides 5V for use with lav mics and such. To power a 48V phantom-powered shotgun mic, you would need an external phantom supply. Regards,...
from the audio ltd website>>>> This cable allows any balanced 48V Phantom powered microphone to be used with a TX2020 or TX2000 transmitter. An in-line power...
Both Denecke and PSC make small supplies that will do what you want. Try Location Sound or Systems Wireless. Chuck ... From: vin To: Lectro@yahoogroups.com ...
Charles Rozner
rozner@...
Nov 6, 2007 1:30 pm
1361
... Try Location Sound or Systems Wireless. Thanks Chuck, I know of them both, but was wondering if there is a much smaller unit... The whole idea was like the...
I've wired up a DPA 4071 lav mic for the SMDA transmitter but the level appears to be low and I need to set the transmitter to the high 30s with audible hiss....
Stephen, The 4071 is a low-sensitivity microphone and the hiss is more a factor of the microphone itself rather than the transmitter. It is common to run the ...
Lectrosonics has wiring for specific lav mic's on their web site, however it is well hidden, and thus not easy to find !! Senator Mike Michaels, c.a.s. Studio...
Senator Mike Michaels
Senator@...
Nov 26, 2007 3:28 pm
1365
Steven, I just realized I had the wrong information in mind about the 4071. That's the higher-sensitivty omni with presence boost. Let me look into a better...
If you haven't already located it, Go to our home page at http://www.lectrosonics.com Go down the navigation bar on the left hand side Click on "Microphone...
Thanks Karl & Senator Mike, I've also read Lectrosonics Wireless FAQ number: 109 on the website. "The servo input transmitters (SM series, UM400a, LMa, UM450)...
Stephen, That looks correct and yes, by lowering the value of the resistor, you should see an increase in gain. Try a 1K, for instance. Regarding the gain and...
According to a recent article on Gearlog.com; the FCC will be accepting final bids for the 700 mhz spectrum by December 28th of this year. For those of us...
I'm trying to set up a R1a to receive two different sources and be able to toggle between the sources with one push of the knob. When I push the knob in to...
If you push multiple times, does it eventually get back to the first stored channel? Does it go to nothing and then back to the second stored channel? Perhaps...
Hi Ed, Although the FCC regs say that we won't be able to use low-powered devices (such as wireless mics) above 700MHz come Feb 2009, the practical issue is...
Ed, you have over simplified it, as the bidding actually begins in Jan 2008. Yesterday was the deadline for prospective bidders to apply to participate in...
Senator Mike Michaels
Senator@...
Dec 5, 2007 3:54 pm
1374
Have you tried erasing all the stored frequencies and starting over? See pages 6,7 in the manual. http://www.lectrosonics.com/manuals/r1aman.pdf...
Hello to everybody. I have a problem with my Venue receivers.I bought it about six months agò in Italy c/o Nagrit . It works very well but from a couple of ...
Andrea Moser
andreamoser@...
Dec 6, 2007 10:17 pm
1376
Did you check the power supply cable? ________________________________ De: Lectro@yahoogroups.com [mailto:Lectro@yahoogroups.com] En nombre de Andrea Moser ...
Mario Nazoa
mnazoa@...
Dec 7, 2007 2:11 pm
1377
Ciao Andrea Try to move your power connector or cfable. If you notice the same fault you find the problem. I have the same problem and I see that the power...
Hi Andrea. Good suggestions from the others. It very well could be the connector. The connector on the Venue has a split pin in the center of the jack. Try...
Thank you Maurizio. I had decided to deliver my Venue receiver to Lectro but now i want to test with a another plug. One year agò i have had a problem with a ...
Andrea Moser
andreamoser@...
Dec 7, 2007 10:34 pm
1380
Hi Bruce, thank you for your suggestion.I already tested the connector and just now i think the problem is inside the plug (i mean in the venue receiver).Maybe...
Andrea Moser
andreamoser@...
Dec 7, 2007 10:35 pm
1381
I am a fan of the short Neumann microphones - the KMR 140, 150, 185 etc. They have served me well on many projects. Lately I have been noticing some noise when...
Hi, I am new to the Block system for Lectros, in news I used fixed freq Lectros. Can I use several mics with several rxs all in the same block ? Which blocks...
it isn't that simple... obviously, the upper blocks (27-29) are going away. Beyond that, you have to determine which blocks will be better in the area(s) you...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
