According to a recent article on Gearlog.com; the FCC will be accepting final bids for the 700 mhz spectrum by December 28th of this year. For those of us...
I'm trying to set up a R1a to receive two different sources and be able to toggle between the sources with one push of the knob. When I push the knob in to...
If you push multiple times, does it eventually get back to the first stored channel? Does it go to nothing and then back to the second stored channel? Perhaps...
Hi Ed, Although the FCC regs say that we won't be able to use low-powered devices (such as wireless mics) above 700MHz come Feb 2009, the practical issue is...
Ed, you have over simplified it, as the bidding actually begins in Jan 2008. Yesterday was the deadline for prospective bidders to apply to participate in...
Senator Mike Michaels
Senator@...
Dec 5, 2007 3:54 pm
1374
Have you tried erasing all the stored frequencies and starting over? See pages 6,7 in the manual. http://www.lectrosonics.com/manuals/r1aman.pdf...
Hello to everybody. I have a problem with my Venue receivers.I bought it about six months agò in Italy c/o Nagrit . It works very well but from a couple of ...
Andrea Moser
andreamoser@...
Dec 6, 2007 10:17 pm
1376
Did you check the power supply cable? ________________________________ De: Lectro@yahoogroups.com [mailto:Lectro@yahoogroups.com] En nombre de Andrea Moser ...
Mario Nazoa
mnazoa@...
Dec 7, 2007 2:11 pm
1377
Ciao Andrea Try to move your power connector or cfable. If you notice the same fault you find the problem. I have the same problem and I see that the power...
Hi Andrea. Good suggestions from the others. It very well could be the connector. The connector on the Venue has a split pin in the center of the jack. Try...
Thank you Maurizio. I had decided to deliver my Venue receiver to Lectro but now i want to test with a another plug. One year agò i have had a problem with a ...
Andrea Moser
andreamoser@...
Dec 7, 2007 10:34 pm
1380
Hi Bruce, thank you for your suggestion.I already tested the connector and just now i think the problem is inside the plug (i mean in the venue receiver).Maybe...
Andrea Moser
andreamoser@...
Dec 7, 2007 10:35 pm
1381
I am a fan of the short Neumann microphones - the KMR 140, 150, 185 etc. They have served me well on many projects. Lately I have been noticing some noise when...
Hi, I am new to the Block system for Lectros, in news I used fixed freq Lectros. Can I use several mics with several rxs all in the same block ? Which blocks...
it isn't that simple... obviously, the upper blocks (27-29) are going away. Beyond that, you have to determine which blocks will be better in the area(s) you...
Senator Mike Michaels
Senator@...
Dec 11, 2007 3:59 pm
1386
Hello there. I'm using the European IFB receivers, and they sometimes fall, and that can damage some small electronic part on the layer/print (?) . Located...
I suppose there are many possible reasons for a failure after the unit gets a good whack and the experts at Lectro can supply better answers than I. But I did...
... Bingo... that's the problem...thanxs :) ..so, it is then the connector between the boards in this specific case, I assume.. Is that a cable, or some type...
I've never seen the connection myself; I've only had it described to me. You'll have to wait for one of the Lectro technicians to sign on and provide better...
Hi Roberto. Sorry to hear you are having problems. And, my apologies for the delay with this reply. Had a visitor and some crisis deadlines today. It could be...
The block system is a grouping of frequencies in 100 kHz steps organized in groupings of 256 each (the "block"). This page on the web site has tables of the...
Thanks Bruce and everyone, my past jobs all used Lectros and so now that I am freelance I bought my own (UCR210D)in Block 25. While seeking the used Lectro...
Hi Michael. Welcome to the group! We try hard to stay on topic in this group by limiting the posts to discussions of Lectrosonics equipment, applications,...
and what make you real :-)? wrong group for advertising try that one http://groups.google.com/group/help-me-need-soundman-gear-mate-for-drink Oleg Kaizerman...
Michael is a brand new member and was just following the advice on the home page to send a "hello" message to the group so his account could be fully activated...
Hi Dino. Welcome! As you may have already read in recent posts, this group tries hard to stay focused on operational and technical issues regarding ...
Hi all, I bought a VR Field in June/07 I already posted my first impressions, but got not very satisfactory answers. In the meantime I´ve worked w/ it about...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
