Is there a way to tell what is the most recent software/firmware version is for SM's? What is the current version? Will the version tell me if I have the +10...
Hi Stacy. The firmware Ver. will be displayed during the boot cycle at power up. The highest firmware Ver. on the SM is 2.2. The +10dB mod requires Ver. 2.0 or...
Hi group I have just received back from the doctors in Rio Rancho a re-furbished MM400A and a new MM400C (replaced damaged 400A) that are now 1.4 versions. The...
Hi Ian. It's Saturday AM here and I can't get to the exact data until later today, but as far as I can tell, the DPA mics need a 3k to 4k resistor in series...
Thanks Bruce. 2 of them were one of the first off the assembly line, I'm sure they don't have the mod. All 4 sound the same. I'll contact service and send them...
Hi Ian. Can't explain why the gain would have changed after the repairs were done. The input circuit has not changed on the MM series transmitters. We wired up...
Thanks Bruce for your thorough checking. My DPA's do not have series resistors but it still seems strange that I have been using them with no problems wired...
Thanks Bruce for your thorough checking. My DPA's do not have series resistors but it still seems strange that I have been using them with no problems wired...
Thanks Bruce for your thorough checking. My DPA's do not have series resistors but it still seems strange that I have been using them with no problems wired...
Thanks, Ian. Sorry for the mystery here. It is strange that they used to work. Still can't explain that, but will nose around a bit with the repair techs to...
Larry or Bruce @ Lectrosonics- I've been looking for info on current draw for the Venue with six receivers. Nothing in the manual or online that I can find......
Hi Don. A mirror image pair of dust covers for the Venue assembly has just been released, but not quite into production yet. Should have them completed in the...
Oops. I sent you the answer to a different email. A fully loaded Venue with 6 VRT modules is the worst case. 17.2 watts So, at 12 volts it pulls 1.43A. At 15...
Please, somebody My 2 lavalier PSC Millimic doesn't work with the transmitter UM400a - with UM400, ok! The connections of TA5-F are as Lectro suggests Some...
Please, somebody My 2 lavalier PSC Millimic doesn't work with the transmitter UM400a - with UM400, ok! The connections of TA5-F are as Lectro suggests Some...
Hi Gabriel. I called PSC to verify the best wiring for the UM400 and UM400a transmitters. They use the 4 volt, 2-wire compatible scheme as shown in the...
different wiring instructions for the 400a !! Senator Mike Michaels, c.a.s. Studio M Productions Senator@... Sound for Film, Video, Radio, TV and...
Senator Mike Michaels
Senator@...
Mar 31, 2008 9:04 pm
1528
The compatible wiring in Fig. 2 of the current mic wiring sheet works with the earlier 5-pin inputs (UM400) and with the servo bias inputs (SM and UM400a)....
As Senator pointed out, there is a wiring that works ONLY with the servo bias inputs. It is a more simple setup than the compatible wiring, but the one we...
I recently decided to purchase a couple of ALP 650's along with 2 4-way passive splitters, 2 BiasT's, and a couple of UFM 230's (just in case I need to amplify...
(not a very technical issue, but ......) I acquired a UCR211, and the on/off switch is recessed inward, enough that I need to use tweaker to flick on/off. I do...
211's are older units, and sometimes older units develop problems, like the one you describe. you need to get it fixed! Senator Mike Michaels, c.a.s. Studio M...
Senator Mike Michaels
Senator@...
Apr 3, 2008 4:03 pm
1534
when the entire transmitting system (including antenna) is enclosed in metal (like inside a car) it will not have the usual range as if it is outside, and if...
Senator Mike Michaels
Senator@...
Apr 3, 2008 4:09 pm
1535
... If the transmittters are on the talent's body and they are inside a vehicle, there will be very little RF signal getting out because the car is shielding...
The switch is mounted so the handle is almost flush to reduce the chance of hitting it accidentally, but it appears that yours may have been damaged. Factory...
I am looking to purchase two used pairs of lectrosonics transmitters and recievers. One pair comes with the 401 and the other with the 411. I've heard the 411...
My Lectrosonics T1 transmittter has become very microphonic and is very sensitive to touch using a metal object like a small screwdriver. Sensitive spots...
If you are making a purchase, you should do some research, homework if you will. you can learn the differences between 401's and 411's from the excellent...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
