Lectro : Messages : 1722-1751 of 2140

Messages: Simplify \| Expand (Group by Topic)		Author	Sort by Date

1722	Hi. I wanted to know if it is possible to use 2 x UFM230 amplifiers in series with each other? If yes, then will the phantom power pass through from one...	nz_harry	Nov 11, 2008 11:26 pm
1723	Unless you're running an extremely long length of coax and the calculated losses warrant two separate gain stages, and even then the added noise floor of the...	H. Cohen henryc@...	Nov 11, 2008 11:49 pm
1724	Harry: Thank you for your message. No unfortunately, you cannot cascade the UFM230 amplifiers with each other you will overload the second amplifer. Sincerely,...	John Muldrow john@...	Nov 11, 2008 11:49 pm
1725	OK thanks for the quick response John. Regards Harry ... each other you will ... power...	nz_harry	Nov 12, 2008 12:02 am
1726	I have four Lectrosonics transmitters in block 29 (two UM400 and two SM) and four receivers in the same block (two UCR401 and two UCR411a) I recently noticed...	gerhardtalan	Nov 12, 2008 6:33 pm
1727	might I suggest you check the RX manuals for adjusting the audio output. it sounds like on RX is set differently from the others, and what do you mean by...	Senator Mike Michaels Senator@...	Nov 12, 2008 6:53 pm
1728	I know that my post was lengthy; but if you had paid attention you would have read "I connected all four receivers to my SQN 4S mixer; set the tone on each...	Alan Gerhardt gerhardtalan	Nov 13, 2008 8:19 am
1729	thanks for the clarification; for some reason I read it that you set the TX's lights to come on. probably the one RX needs to go to the hospital to get made...	Senator Mike Michaels Senator@...	Nov 13, 2008 4:05 pm
1730	Hi Alan. Ran this by one of our leads techs to see if it looked like a common problem and to get his opinion. He said one suspect component is the digital pot...	brucejones87124	Nov 13, 2008 8:54 pm
1731	We have some problem about Venue system. We are using 12 venue 29 block wideband receiver and 12 smd transmitter. The problem are 1. very week RF signal we are...	wavemgusa	Nov 17, 2008 4:33 am
1732	Hello all. I'm new to the group and glad to find yall here. I'm using a 400 Transmitter and 411a Receiver. The battery meter on the receiver is completely...	bradsrecords	Nov 17, 2008 3:50 pm
1733	What country and city are you in? We may have a dealer close to you who can help....	brucejones87124	Nov 17, 2008 4:03 pm
1734	What is the serial number and firmware revision of your UCR411A? The firmware revision appears briefly at power up with two numbers on the LCD....	brucejones87124	Nov 17, 2008 4:08 pm
1735	I'm going to stick my neck out here, and say that it might need to return to the mothership for some TLC !! Senator Mike Michaels, c.a.s. Studio M Productions ...	Senator Mike Michaels Senator@...	Nov 17, 2008 10:07 pm
1736	Thanks Bruce, I have the day off. Will check tomorrow and let you know. ... the LCD. ... can put ... from ... a...	bradsrecords	Nov 18, 2008 5:52 pm
1737	Newbie just checking in. Carroll Senn Engineer Gamecock Radio Network 803-429-2114 Mobile Email: csenn@... [Non-text portions of this message have been...	Carroll Senn cwsenn	Nov 19, 2008 2:51 pm
1738	Welcome to the group! Thanks for joining! This group is low traffic and we try hard to stay on topic. It is moderated to block spam and off topic posts. The...	brucejones87124	Nov 19, 2008 4:19 pm
1739	Hi Output levels on the EMW are much much hotter than my COS11. Wiring is standard on both, I wonder if i have to put in a resistor... -vin...	vin soundtrane	Nov 22, 2008 7:13 am
1740	do you have a low output version of the cos11? try this http://www.countryman.com/display.asp?catid=4&pid=75 http://www.lectrosonics.com/hybrid/sm/smwiring.pdf...	kapshome@... bill1709	Nov 22, 2008 9:52 pm
1741	... the wiring is as the c'man page suggests, i dont think my COS-11's are low output... -vin...	vin soundtrane	Nov 23, 2008 12:44 am
1742	Thanks, Bill. Oops. The link to the wiring document should take you here: http://www.lectrosonics.com/service/ServoBiasWiring.pdf Sorry. Will remove the older...	brucejones87124	Nov 24, 2008 4:07 pm
1743	SN:6092 Firmware: 4.1/4.0 I failed to mention that this gear is owned by the production company. Has been used by many mixers, and has'nt been cared for the ...	bradsrecords	Nov 24, 2008 4:20 pm
1744	tell them it is broken! Senator Mike Michaels, c.a.s. Studio M Productions Senator@... Sound for Film, Video, Radio, TV and PA ... From:...	Senator Mike Michaels Senator@...	Nov 24, 2008 5:23 pm
1745	If the problem is consistently present in different locations on clear frequencies, it looks like it's time for a trip to the repair bench. The following reply...	brucejones87124	Nov 24, 2008 5:50 pm
1746	yeah, that's what I meant!! Senator Mike Michaels, c.a.s. Studio M Productions Senator@... Sound for Film, Video, Radio, TV and PA ... From:...	Senator Mike Michaels Senator@...	Nov 24, 2008 6:22 pm
1747	Thanks. I think they're gonna take my/your advice and send it in and rent another one in the meantime. ... the ... UCR411A? ... numbers on ... drop ... ...	bradsrecords	Nov 25, 2008 2:20 am
1748	Sorry, I am at a loss. I have used but do not own any. I am sure some one will post a possible fix. Happy Turkey day to all. Bill ...	kapshome@... bill1709	Nov 27, 2008 8:39 pm
1749	I have a request from our production group. They want multiple people to be able to hear the program audio on ENG shoots. Is it posiable to connect a beltpack...	tconstan68	Nov 28, 2008 2:24 am
1750	When you say "program audio," are you refering to field acquisition (camera) audio, or audio from a broadcast, which is typically refered to as "program audio"...	Mike Meinhardt Mike116@...	Nov 28, 2008 2:33 am
1751	Thanks Mike, I said Program audio but I mean camera audio (from camera line out) or sometimes audio out from a field mixer. In any case you have answered my...	tconstan68	Nov 28, 2008 11:24 am

Yahoo! Groups Tips

Did you know...

Messages

Yahoo! My Yahoo! Mail
	Sign In New User? Sign Up
		Tech - Groups - Help

Yahoo! Groups Tips

Did you know...

Best of Y! Groups

Messages