I have two Lectrosonics. They are UCR205D receivers with the UM200C transmitters, Block 24. My issue is suddenly one of the units is getting a weak RF signal,...
It is very unlikely that two systems would fail simultaneously with similar symptoms. This give rise to suspicion that there is another component involved that...
If both systems started to exhibit poor RF performance at the same time, my initial question would be if you had them tuned within the same TV channel. If so,...
H. Cohen
henryc@...
May 19, 2009 2:31 pm
1932
" My issue is suddenly one of the units is getting a weak RF signal...The other unit is outputting only two lights and not receiving audio " OK, you really...
Senator Mike Michaels
Senator@...
May 19, 2009 3:20 pm
1933
Bruce, Thanks for your help. I have switched out antennas between the two units. They are the original whip antennas that came with the system. I have the...
if you have the TX and RX near each other, turned on, and on the same frequency setting, and you only get 2 signal strength lights, AND the TX works fine...
Senator Mike Michaels
Senator@...
May 19, 2009 4:28 pm
1935
fixing typo: if you have the TX and RX near each other, turned on, and on the same frequency setting, and you only get 2 signal strength lights, AND the TX...
Senator Mike Michaels
Senator@...
May 19, 2009 4:48 pm
1936
As was suggested, the best diagnosis is the process of elimination using a transmitter that works with another receiver. Your earlier post, however, stated...
Hi Stephen. Shipments to Europe will commence in late June and July to Europe. This is our return after several years of converting to lead-free, RoHS...
what Bruce meant to say was: "The difference between the 400 series and the 500 series is the power output of the transmitters (100 to 250 mW in the US and...
Senator Mike Michaels
Senator@...
May 23, 2009 4:43 pm
1940
Hi Group I have just completed a 5 month tv series using SR5P Rx's mounted in the slots on 2 x XD cams. I used the 5PXLR2 cable to input the audio into the...
Hi Bruce et al. I want to remove the beltclip from my UM400. The beltclips on my UM200's came off with no hassle, but the 400 is extremely tight. Which brand...
Thanks for all of the information Bruce! Someone at Lectro Toronto (Joe?) read my post and supplied me with the appropriate hex key and replacement screws! (I...
I don't believe so, unfortunately. But, if using it as a camera hop, it isn't really a concern unless a transmitter is going to come within a foot of the...
nope it does not, just think of it as 2 pcs of 401s. it generally isnt a problem unless u are sending a headphone feed back to u or tapping the TC out. if so,...
Group, Can anyone tell me the cut-off voltage for a UM400? I have been watching the Tx battery meter lately (on the Rx) and it shows 1/2 or more full, but...
the full charge lithium ion would give not more then 8.4 v , completely discharge about 6.8 -6.6v even there is enough voltage ( lector would work till 6 v )...
What I forgot to mention was that I don't like to run the IPowers down below 7.1v. I wonder if it is possible to recalibrate the battery meter to give a 'low...
Hi Jason. Oleg hit it right on the nose. The switching supply is turned off at 6 volts. It's not in the manual or data sheet, so I wonder how he knows that? He...
(Sorry, I am a blabbermouth) If you use the timer, you will need to check each battery, because the total run time on older ones will be less than on newer...
Thanks for the info Bruce and Oleg. -Jason To: Lectro@yahoogroups.com From: opusstuf@... Date: Tue, 23 Jun 2009 19:57:43 +0000 Subject: [Lectro] Re:...
I just bought some used 211's and 201's, and have attempted to power them through the 12v output jacks on my M4MKII mixer. I hear a background hiss when...
Hi Pete. Great detective work! In my opinion, you would be better off using a modified cable or barrel adapter to deal with the problem, rather than altering...
I Have 2 lectro sr receivers..ch1 output is 5 to 10 db lower than ch 2. both are set at +5. Then this week the second unit has done the same thing. Even when...
Thanks for the info! Lifting the ground at either end of the audio cable did not work. I tried strapping pin 1 to the connector shells on the cables. The...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
