Thanks for all of the information Bruce! Someone at Lectro Toronto (Joe?) read my post and supplied me with the appropriate hex key and replacement screws! (I...
I don't believe so, unfortunately. But, if using it as a camera hop, it isn't really a concern unless a transmitter is going to come within a foot of the...
nope it does not, just think of it as 2 pcs of 401s. it generally isnt a problem unless u are sending a headphone feed back to u or tapping the TC out. if so,...
Group, Can anyone tell me the cut-off voltage for a UM400? I have been watching the Tx battery meter lately (on the Rx) and it shows 1/2 or more full, but...
the full charge lithium ion would give not more then 8.4 v , completely discharge about 6.8 -6.6v even there is enough voltage ( lector would work till 6 v )...
What I forgot to mention was that I don't like to run the IPowers down below 7.1v. I wonder if it is possible to recalibrate the battery meter to give a 'low...
Hi Jason. Oleg hit it right on the nose. The switching supply is turned off at 6 volts. It's not in the manual or data sheet, so I wonder how he knows that? He...
(Sorry, I am a blabbermouth) If you use the timer, you will need to check each battery, because the total run time on older ones will be less than on newer...
Thanks for the info Bruce and Oleg. -Jason To: Lectro@yahoogroups.com From: opusstuf@... Date: Tue, 23 Jun 2009 19:57:43 +0000 Subject: [Lectro] Re:...
I just bought some used 211's and 201's, and have attempted to power them through the 12v output jacks on my M4MKII mixer. I hear a background hiss when...
Hi Pete. Great detective work! In my opinion, you would be better off using a modified cable or barrel adapter to deal with the problem, rather than altering...
I Have 2 lectro sr receivers..ch1 output is 5 to 10 db lower than ch 2. both are set at +5. Then this week the second unit has done the same thing. Even when...
Thanks for the info! Lifting the ground at either end of the audio cable did not work. I tried strapping pin 1 to the connector shells on the cables. The...
Hi Peter. More info from engineering regarding the grounding and fusing scheme in the UCR211 and UCR201... <<The problem with the 211's and 201's is not so...
ground loop issues can be major pains!! Senator Mike Michaels, c.a.s. Studio M Productions Senator@... Sound for Film, Video, Radio, TV and PA ...
Senator Mike Michaels
Senator@...
Jul 7, 2009 4:48 pm
1961
Have been checking around since your first post to see if this same symptom has come up elsewhere. We have had a couple of units here and 2 or 3 in the New...
Hello there professionals. The audio file below is from a recent shoot where I used a SR on a HVX200. I sent two channels to the SR from my mixer with two...
Hi Bryan, Sounds like loss of RF, maybe? I assume you checked the cables and that was not the issue. What band/channel were you using? What are all 4...
... Hi Bryan, I listen to the audio a couple of times and it sounds like a interference from two way radio as I had something similar while recording with the...
Hi Guys this is not related to lectrosonic so I understand if it is not publish. I am looking for the connector on the comms systems of the MRAP vehicles in...
Hi, What type of resistor should I use inside the ta5f connector of my COS-11's? Will regular 1/4 watt fit? Do they make smaller sizes that will fit/work...
Hello David Bogie David Bogie Eagle Eye Digital Video <http://www.eagleeyedv.com/> www.eagleeyedv.com 651-485-3153 Fax: 1-866-264-7121 [Non-text portions of...
David Bogie
dave@...
Jul 20, 2009 7:56 pm
1970
Hello Everyone, My name is Dave and I own a company that sells a unique application for timing sporting events and I am in need of some assistance and...
David Bogie
dave@...
Jul 20, 2009 7:58 pm
1971
Is anybody aware of any FCC restrictions on wideband transmissions, my local radio supplier said that wideband will be restricted in some fashion after 2013....
David Alley
alleydg@...
Jul 20, 2009 7:59 pm
1972
first of all, you do not understand the terminology "wideband" used to describe the "Venue Wideband"; that description means the front end antenna circuits...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
