Hello All, In case anyone should come across a new, full umc200d rack of ucr211's please check the s/n's. I had an rf rack stolen from a van outside of Boston...
I recently saw on ebay a rack of T1's in the umc200d rack mount. Picture clearly shows the power leads being used but not the antenna leads. This seems like a...
Hi Pat: It would be nice to combine 4 transmitter outputs through a passive multi-coupler to share a common antenna, but it is not that simple. In a 4-way...
I am a crestron programmer and I am using Lectrosonic Mixer Am 8 in my automation I require some help with this regards.. Can anyone help me with this.? Roshan...
Roshan look up Lectrosonic web site you can download all the details you will require. www.lectrosonic.com Muschy ... From: "roshgujarathi"...
John Musch
muschy@...
Jun 21, 2003 11:30 am
281
I just bought a 411 receiver and a MM400a transmitter and i found it very noisy compare to my two 210D even with the full noise reduction( i can't even think...
From July 28 to September 12, 2003 I will be in Regina, Saskatchewan. I will be checking e-mail 3x per week. Thank you for your understanding. Thomas Hayek ...
The 400 Series system is at least as quiet as a 210 system. The MM400a input preamp is also very quiet. Something else is going on here. Please bear with us...
From July 28 to September 12, 2003 I will be in Regina, Saskatchewan. I will be checking e-mail 3x per week. Thank you for your understanding. Thomas Hayek ...
New member looking for some answers. My "not-on-line" brother (Billy Kennedy) is a guitar picker in Portland, OR and is looking for information on an amp...
Im using the microphone that was sent to me by lectro the m150 on both systems, i'm monitoring from a 442 from Sound Devices and beyers dt-48 headphones the...
Greetings, My name is Brian. I live in the Seattle area. I have been looking for a "maxi mouse" amplifier as well. I believe the production ceased in 2000....
Most of the Maxi Mouse amps were sold through dealers in New York City, especially along 48th street in Manhattan. There should be second-hand units still...
Hi Alan: The UCR200D was the very first compact receiver in the 200 Series product group. It ran from external power only, pulling a hefty 400 mA. Heat was...
Thanks Bruce for your reply, I'd just confirmed my purchase for a used UCR200D system (Blk22), it will be running together with my 3 x 201 (Blk 22,25,26), the...
Almost forgot, is there an factory upgrade for the 200D Rcv? Maybe to a lower powering requirement? If yes, is it a free upgrade? Thanks Alan Chong ... ...
Alan, I'm running two 210D receivers, two UN250C transmitters (high powered transmitters for wireless link), and a T2 IFB transmitter off the Remote Audio BDS...
Paul Kucharski
pkuch@...
Aug 1, 2003 7:53 pm
294
Hi Paul, I'm using the BDS V2, but as u know I'm also powering my mixer together with a same battery so therefore the concern of power management. M4MkII,...
Hello again Alan: The UCR200D pulls 400mA by design. Unfortunately, there is no update or modification that can change this. If you add up all the numbers...
My biggest concern would be the whopping 400mA draw of the 200D. I figure my twin 250C's are probably drawing close to 300mA each in order to transmit at 1/4...
Paul Kucharski
pkuch@...
Aug 1, 2003 8:27 pm
297
Thanks to all I think 2 NP NIHM / Li-on batteries will be the bare minimum for a 10/12 hrs day (assuming an wireless day). Lets sidetrack abit, does anyone...
Hi Paul: Thanks for your posts. Much appreciated. The rated power consumption for the UM250C transmitter is just under 120 mA. The UCR210D receiver is rated...
Oops. I can't add. Correction on my last post. Didn't read how many units you are using. 2 x UM250C at 120 mA each = 240 mA 2 x UCR210D at 130 mA each = 260...
Bruce, Since it seems you did not get the e- mail I sent you. The antenna to my UM 195B (Freq. 589.950 Mhz, S/N 3184) is damaged and I would like to buy a new...
Suresh Rajamani
suresh1@...
Aug 2, 2003 3:08 pm
301
Hello, I am shooting a doc/reality show right now and am using two Lectro 201s to send signals to the camera ops PD 150. He is carrying them in a fanny pack ...
Tom: Can't be certain this is VERY similar to a situation we found a couple of years ago. If you take a 9V battery, SHORT the contact with a penny or bare...
Gordon Moore
gordon@...
Aug 4, 2003 5:02 pm
303
... From: "Gordon Moore" <gordon@...> To: <Lectro@yahoogroups.com> Sent: Monday, August 04, 2003 11:02 AM Subject: Re: [Lectro] Heat issues with...
amdcatr
amdcatr@...
Aug 5, 2003 4:15 am
304
Hello all, just got a gig that I have to do using lectro UM200C and I have never used them before, I have to shoot aug 7th all day b- roll with them, could...
800-821-1121 but I doubt the Customer Service department is open now. You might also try 505-892-4502 and hope for someone who happens to be working late. I'm...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
