Is it possible to get the bottom mounted TX aerials on Lectro 195's converted to the top plate? Regards Peter Kraan. [Non-text portions of this message have...
Hi Peter: Unfortunately, there is no way to convert the bottom mount antenna to the control panel (top panel). The boards and mechanical parts are different,...
To: <Lectro@yahoogroups.com> From: "Peter Kraan" <p.kraan@...> Date sent: Wed, 3 Mar 2004 20:29:00 +1300 Subject:...
Gordon Moore
gordon@...
Mar 4, 2004 5:59 pm
393
Peter asked, "Is it possible to get the bottom mounted TX aerials on Lectro 195's converted to the top plate?" Alas, the answer is no. The UM195B was a...
Gordon Moore
gordon@...
Mar 4, 2004 6:08 pm
394
Bruce, I noted your comments on system compatability with interest. If I wish to use a Block 24 MM400a with a UCR195D, does the UCR195 need to be operating...
Hi Mike, The receiver and transmitter must be in the same block, so the answer to your question is yes, the UCR195D would have to be in block 24, and no, the...
Hello - I have 2 sets of UCR190 receivers and UMD190B body pack transmitters and would like to add a plug-on transmitter to each set. What current Lectro...
por favor gostaria de saber se vc´s tem representante no Brasil THOR MEDEIROS S.D.A som direto associados [Non-text portions of this message have been...
THOR MEDEIROS
thormedeiros@...
Mar 12, 2004 7:44 pm
398
I note on the data sheet of the mm400a that Block 23 is now included. I had understood that previously this block was not available in the US Lectrosonics...
Hi Mike Block 23 encompasses at the upper end the world-wide allocation for radio astronomy. It isn't there to avoid conflicts / intermod. So you only have...
Thanks John. I have always been aware that 100 and 200 models were not available in Block 23 unless you looked at the European versions with lower transmitter...
Hi Mike Hope you didn't mind my joke. Noticed your new premises on your site, looks good. Found out recently that NZ was part of Australia 80 million years...
Yes I' all for sharing the crumbs with the needy! But seriously we've got 2 very large productions gearing up the middle of the year apart from the run of the...
There are thoughts that digital radio mike systems may be unaffected by un-suppressed vehicle ignition systems. Conversly, the fact that the transmission...
Block 23 has been available some time now - all you lose is the 6MHz of the astronomy band - consider it a permanent TV band. You still have the remaining...
Gordon Moore
gordon@...
Mar 22, 2004 6:26 pm
405
Sorry for the delay in this reply. Have been out of town a lot lately. Your units were built on these frequencies: UCR190 #6641 and UM190B #3326 - 562.675 MHz...
Dear Gorden, Bruce: Hi. First time try to post my questions: 1) Did factory have any idea to develope a inexpensive 400 series receiver supposed named UCR401A...
Steven from China asked - ... receiver supposed named UCR401A similiar as UCR201 in 200 series? Or we just take advantage of current UCR201 to forge a pricy...
Gordon Moore
gordon@...
Apr 12, 2004 3:30 pm
409
Requested file. [Non-text portions of this message have been removed]...
jimmy@...
Apr 22, 2004 11:54 am
410
I'm looking for the sales representation in Mexico, Florida or Brazil. Thanks Cesar Salazar. Colombia __________________________________ Do you Yahoo!? Win a...
Cesar Salazar
cesalaber@...
Apr 28, 2004 4:09 pm
411
I have a UDR200B receiver w/ UT200-87 transmitter. The battery voltage on the UDR200B display shows sometimes and then goes away. In addition, the voltage...
Dear Sales, We are using Lectrosonic make UHF mikes type UM-95/UCR-195 ,can you please supply 6 No's of Tx. antennae and 12 no's of Rx. antennae for above type...
Jawahar lal
jawahar@...
May 4, 2004 10:05 am
413
I am wondering if it possible change the frequency of a UH195 UHF Plug-On Transmitter from 585.950 MHz to 607.950 MHz? How much would that cost?...
This is my second UHF Bodypack system i have purchased but the RF light on this lectrosonics receiver does not light up until about 5 to 10 min , What could be...
Ian Guthrie
jiggaprezident@...
May 16, 2004 7:06 pm
415
Double check your frequency settings - make sure they absolutely match - it's really easy to be off one click on the 100Khz (the right one) and still get some...
Gordon Moore
gordon@...
May 17, 2004 3:10 pm
416
Hi I've been using my 3 units of UCR 411 for the past 2 month, something which I realise during the shoot is that, when changing of UM400 TX batteries without...
Hi Alan: Having to reboot the receiver does not sound right. Will investigate and get back to you. You can e-mail the warranty cards. Just need model number,...
Per your separate e-mail to Larry Fisher regarding your firmware versions: Firmware versions for UCR411 SN audio PCB Ver, 2.2 RF PCB Ver. 3.0 Firmware version...
... This only happen on UCR 411 - SN 827 / UM400 - SN 938 set. As I'm on my break now, I will check with my replacement sound guy for the firmware rev. Alan...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
