I have a UDR200B receiver w/ UT200-87 transmitter. The battery voltage on the UDR200B display shows sometimes and then goes away. In addition, the voltage...
Dear Sales, We are using Lectrosonic make UHF mikes type UM-95/UCR-195 ,can you please supply 6 No's of Tx. antennae and 12 no's of Rx. antennae for above type...
Jawahar lal
jawahar@...
May 4, 2004 10:05 am
413
I am wondering if it possible change the frequency of a UH195 UHF Plug-On Transmitter from 585.950 MHz to 607.950 MHz? How much would that cost?...
This is my second UHF Bodypack system i have purchased but the RF light on this lectrosonics receiver does not light up until about 5 to 10 min , What could be...
Ian Guthrie
jiggaprezident@...
May 16, 2004 7:06 pm
415
Double check your frequency settings - make sure they absolutely match - it's really easy to be off one click on the 100Khz (the right one) and still get some...
Gordon Moore
gordon@...
May 17, 2004 3:10 pm
416
Hi I've been using my 3 units of UCR 411 for the past 2 month, something which I realise during the shoot is that, when changing of UM400 TX batteries without...
Hi Alan: Having to reboot the receiver does not sound right. Will investigate and get back to you. You can e-mail the warranty cards. Just need model number,...
Per your separate e-mail to Larry Fisher regarding your firmware versions: Firmware versions for UCR411 SN audio PCB Ver, 2.2 RF PCB Ver. 3.0 Firmware version...
... This only happen on UCR 411 - SN 827 / UM400 - SN 938 set. As I'm on my break now, I will check with my replacement sound guy for the firmware rev. Alan...
I think I recall having something similar happening with either a 211 or a 201 of mine. No audio while apparently solid RF, had to reboot rcvr. Paul Kucharski ...
Paul Kucharski
pkuch@...
May 25, 2004 1:35 am
422
... Bruce, The firmware is 2.2/3.0 on the unit. Alan Chong...
Hi Alan: Should have asked this yesterday, but did not think of it. Are the firmware versions the same on the other two UCR411 receivers that work OK? ... have...
If they are all the same firmware revison, and only one system is acting up, then it must be broken. Will check with service, but my guess is that it will...
I need help!! I'm looking for a store in Chicago or N.Y, that sale antennas for UM200C blk 22. Thanks. Cesar Salazar Bogota-Colombia ...
Cesar Salazar
cesalaber@...
May 26, 2004 4:55 pm
428
... Hi Bruce Kindly send me an RA number, the TX is dead now, UM400 - SN938, UCR411 - SN 827. This set is the latest that I bought from Gotham Sound. How will...
I have a UDR-200B receiver. Tha pilot tone will not lock when receiving. *I have tried several transmitters that work fine on other receivers. *The receiver...
It sounds like the pilot tone crystal is gone. Will forward your message on to our service folks for follow up. Fortunately, you can continue to use the...
Bruce, I've come across this problem many times with the UM200 tx's. Why is this such a problem with these crystals? In my mind this is the one serious flaw...
Timothy D. Paul
tpaul@...
Jun 7, 2004 7:24 pm
432
I am trying to use the programmable outputs with a Digital I/O PC card. What the I/O card needs, is a +5V feed into each of its sixteen connectors to capture...
Need some ideas for a permanently mounted external IFB antenna on a remote news van. Some features it needs or is highly desired: * This is for Lectro IFB...
finally, a question that is more than just whining: "do I have to send it in for service?" a full size 1/4 wave whip, roof mounted, yes another one! and try to...
Senator Mike Michaels
Senator@...
Jun 15, 2004 5:49 pm
435
Having the ability to move the transmitter indoors is a huge plus. I know we'd all like to use one permanently mounted T1, but there are too many situations...
Paul Kucharski
pkuch@...
Jun 15, 2004 6:15 pm
436
Hi there, Can used quad box (which has wrong block for me) be easily modificated to another block (block 31)? Thanks, Pietari Koskinen <-> <-> <-> <-> <-> <->...
Hi Pietari: The QUAD BOX was a VHF or UHF compatible unit. Check to see what the exact model numbers are on the installed multicoupler modules. The CDM4...
... modificated ... Hi Pietari: I have been told that a quad box distribution amp can be modified to operate on another block. For starters I would need to...
... modificated ... Hi Pietari: I have been told that a quad box distribution amp can be modified to operate on another block. For starters I would need to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
