I am looking for a good new listeroid 6/1 , any brands out there better than another ? I dont have the time to tear down an engine and clean sand etc. Central...
... I have a GTC model, purchased from: http://ecodieselcanada.com/?s=1&p=11 The factory page: http://www.geco-trade.com/productitems.asp#anc3 There are two...
echo4
echo4@...
Sep 5, 2008 5:03 pm
7239
Hi Folks, Been a while since I posted anything. Still have the CS in the garage only now getting round to getting it up and running proper. I have been...
Acronyms, acronyms! AV means AVailable, Automatic Voltage, Amateur Video? Just don't put flexible mountings only under the engine. Put them under the engine...
Hi pete , I tried rubber "barry mounts " on my Lister 8/1, designed for use on power presses ( very good quality) Ideal you might think! NOT SO . Nearly gave...
Pete, List Anti-vibration mounts are usually intended for 1500rpm operation. They will not be effective at the 650rpm (850rpm) of the standard slow speed...
My Tico pads are effective, I think, but then again the frame, with engine and genny, on the pads are mounted on a block separate from the surrounding floor....
... I would suggest dicussing the application with the company who manufactures the mount in question. There a number of different manufacturers and designs....
Hi Folks, Thanks for all the feedback I,ll digest and have a think. The only issue I have is that it is on a concrete floor already and wondering if I can...
Dear Listers Has anyone actually followed Manufacturer's Instructions and actually built a Lister Foundation like they recommend? How well do they work? Any...
Can anyone tell me where this part fits on a CS 6/1. It is a round spacer washer 1" outside dia, 13/16" inside dia and 11/32" thick. I am comming to the end of...
Try: http://www.vibrationmounts.com/Store.asp?Page=Products1.htm Mark ... stamping ... machines of ... inside of ... are ... on the ... the ... Sorry I'm ... ...
... Thanks Rab, Yes your right, that's what it is!!. Do you know if it is essential to have this in place? as I have already re assembled the head to the...
Hi all, well, do dynamo have a starting voltage, IE 6v, 12v, 24v, or do they start fron 0 and the more you rev the more volts you get. I was looking to charge...
Dear Peter ... From: peterhynman To: Lister_CSOG@yahoogroups.com Sent: Wednesday, September 10, 2008 11:34 AM Subject: [Lister_CSOG] dynamo Hi all, well, do...
... you know if it is essential to have this in place? .............................well they would not have fitted them if they were not needed, would they? ...
... wrote: Hi all, well, do dynamo have a starting voltage,..........Yes they do. Zero revs equates to zero volts output. As the revs increase so will the...
thought i would share what i saw on the news that a Steam show looks free is held this week,looked liked they had some lister engines as well as tractors...
the needed those mounts at a hotel i was staying at! :) Thomas Edison told his friends Henry Ford and Harvey Firestone: “I’d put my money on the sun and...
... Lister probably used them because it was 'good engineering practice' and 'how things are done'. Many (most?) of the Indian engines do without them with no...
... Oh dear, how depressing that quote is ... and its started to rain again here (Cotswold Hills). Wettest UK summer for decades apparently, no doubt the GW...
M.Blackmore
mblackmore@...
Sep 11, 2008 11:45 am
7261
Many (most?) of the Indian engines do without them with no apparent problems.>>>>>>>>>>>>They are prob'ly aligned by the studs or smaller tolerance holes in...
Thanks Rab & Paul, Removed the head last night and found that the new cylinder block that I have fitted does not have the recesses to take the locating...
Hi I have a 12/2 running at 325 and it works great when compared to a 6/1. The noise is a lot less and the governor spring was changed to a longer, softer...
sarawnw wrote: I have a 12/2 running at 325 Good to hear you are happy at 325rpm. The only thing I would be careful of is overloading it at that speed as the...
Dear Sara and Charlie One downside of running an engine at half its rated output is that the Specific Fuel Consumption will be higher. Kevin ... From: sara...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
