Hello All After further homework I have found that information in JLN's report and that found in Tom Bearden's Original paper megpaper.pdf, does not show the...
Hi Ken et al Nice explanation of how to make a carbon film resistor. (Ken) The carbon resistor link that Bob found has 5 Watt "carbon film" resistors and 2...
Hello all I have acquired a very large Metglas core (AMCC-1000), a large 2x2x1.5 neodymium magnet and am on my fourth generation of a control switcher for the...
... eq. which is that a magnetic field can be produced without current flowing in the wire. ... primary would not draw any power... or would it? ... Not a...
http://www.geocities.com/nayado/ ... Odchozí zpráva pravděpodobně neobsahuje viry. ... "Never underestimate the power of human stupidity." ("Nikdy...
gewo
gewo@...
Sep 4, 2002 4:32 pm
1061
Hello everyone. I have seen the occasional message recently from people embarking on their first attempts at replication. This requires alot of effort,...
Steve I read nothing about a special resistor in the patent material either. Looks like the picture of the patent device has wire wound resistors to me too. ...
... an ... red ... CRT..bound ... To Late, I tried it last weekend and it works great. I fried a couple of 120kOhm carbon resistors. The resistor reaches a...
Thanks Norm, Seemed to me like a possibility to get rid of the back-EMF from the secondary to the primary in the MEG when switching the flux. And the best to...
Is Honeywell part no. AMCC-630 the part that Bearden has used? http://www.metglas.com/downloads/powerlite.pdf Also what material seems to be the best of the...
Clay I bought "the recommended" Metglas core(AMCC-320) which is 129mm(5") long, 79mm(3") tall and 50mm(1.9") deep. Paid $86 for it. I believe that is the one...
... Based on the dimensions in the patent, and the core- material referenced, the core is the AMCC-630. I bought one, and it is slightly larger than JLN's...
Hello Guy et al I am not sure you only meant to send this to me instead of MEG_builders@yahoogroups.com but I will answer as if you did intent it as a post so...
... Hello everyone, I am a new builder of MEG in France. For 2 months I have built a MEG with AMCC-320 and the signals forms are the same one as Tom BEARDEN. ...
Hello Guy et al I am not sure you only meant to send this to me instead of MEG_builders@yahoogroups.com but I will answer as if you did intent it as a post so...
... From: robert_bielik [mailto:robert.bielik@...] Sent: Monday, September 16, 2002 2:49 AM To: MEG_builders@yahoogroups.com Subject: [MEG_builders]...
re: Purpose of one-shot prior to driver circuit. Bearden states repeatedly that voltage, not power, into the MEG has a direct COP relationship. One has only to...
... some ... fashion ... take more ... Since the ... core I ... core. ... see the ... Dear Bob The coil looks great! How did you do it? Norm Fletcher...
Norm ... patent ... voltage ... I don't quite follow what you said there. Voltage causes current and the product of voltage and current is power.... so if...
All I am almost ready to start measuring the gain of my MEG. I would like to hear how some or all of you think input and output power should be measured. I...
Hi Bob, I have some ideas, for all to comment on. See below. ... For input I think it suffices to measure the RMS voltage and current from the power supply,...
... power ... battery while ... charge on ... Bob W., Here's some of my thoughts for what they are worth ... Re: measuring input power. Providing that your...
. What did I miss... ... Bob I was talking about input power remaining the same throughout the input voltage range. In other words, if the VOLTAGE INPUT...
... battery while ... charge on ... To Bob and ALL I have the same question about output determination. My MEG acts like a poorly efficient transformer so far...
Hi, I just have a couple of questions. First, is this a powered generator and if is what is the power in vs the power out? Secondly, how exactly does it work? ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
