Hi, I just have a couple of questions. First, is this a powered generator and if is what is the power in vs the power out? Secondly, how exactly does it work? ...
1084
ecolynx_com
Oct 2, 2002 4:01 pm
Hello: EcoLynx.com recently added two new pages devoted exclusively to zero point energy. They are: Zero Point Energy - Follow the Lynx! (URL:...
1083
fletchmo47
Sep 29, 2002 2:07 pm
... battery while ... charge on ... To Bob and ALL I have the same question about output determination. My MEG acts like a poorly efficient transformer so far...
1082
fletchmo47
Sep 29, 2002 2:07 pm
. What did I miss... ... Bob I was talking about input power remaining the same throughout the input voltage range. In other words, if the VOLTAGE INPUT...
1081
Stan Mayer
mayerstan
Sep 27, 2002 5:29 pm
... power ... battery while ... charge on ... Bob W., Here's some of my thoughts for what they are worth ... Re: measuring input power. Providing that your...
1080
robert_bielik
Sep 27, 2002 3:38 pm
Hi Bob, I have some ideas, for all to comment on. See below. ... For input I think it suffices to measure the RMS voltage and current from the power supply,...
1079
BobW
rmwinchester
Sep 26, 2002 1:11 pm
All I am almost ready to start measuring the gain of my MEG. I would like to hear how some or all of you think input and output power should be measured. I...
1078
BobW
rmwinchester
Sep 26, 2002 1:11 pm
Norm ... patent ... voltage ... I don't quite follow what you said there. Voltage causes current and the product of voltage and current is power.... so if...
1077
fletchmo47
Sep 24, 2002 7:52 pm
... some ... fashion ... take more ... Since the ... core I ... core. ... see the ... Dear Bob The coil looks great! How did you do it? Norm Fletcher...
1076
fletchmo47
Sep 24, 2002 7:52 pm
re: Purpose of one-shot prior to driver circuit. Bearden states repeatedly that voltage, not power, into the MEG has a direct COP relationship. One has only to...
1075
BobW
rmwinchester
Sep 17, 2002 3:59 pm
Rob et al ... From: robert_bielik [mailto:robert.bielik@...] Sent: Monday, September 16, 2002 2:49 AM To: MEG_builders@yahoogroups.com Subject:...
1074
BobW
rmwinchester
Sep 17, 2002 12:10 am
... From: robert_bielik [mailto:robert.bielik@...] Sent: Monday, September 16, 2002 2:49 AM To: MEG_builders@yahoogroups.com Subject: [MEG_builders]...
1073
robert_bielik
Sep 16, 2002 5:53 pm
Hi Bob, ... Have you done any experiments on comparing normally and bifilar wound input coils with respect to CEMF and flux rise/fall times? /Rob...
1072
BobW
rmwinchester
Sep 16, 2002 2:33 am
Hello Guy et al I am not sure you only meant to send this to me instead of MEG_builders@yahoogroups.com but I will answer as if you did intent it as a post so...
1071
ardeshe2000
Sep 16, 2002 2:33 am
... Hello everyone, I am a new builder of MEG in France. For 2 months I have built a MEG with AMCC-320 and the signals forms are the same one as Tom BEARDEN. ...
1070
BobW
rmwinchester
Sep 16, 2002 2:33 am
Hello Guy et al I am not sure you only meant to send this to me instead of MEG_builders@yahoogroups.com but I will answer as if you did intent it as a post so...
1069
davidj95650
Sep 11, 2002 8:27 pm
... Based on the dimensions in the patent, and the core- material referenced, the core is the AMCC-630. I bought one, and it is slightly larger than JLN's...
1068
BobW
rmwinchester
Sep 11, 2002 8:26 pm
Clay I bought "the recommended" Metglas core(AMCC-320) which is 129mm(5") long, 79mm(3") tall and 50mm(1.9") deep. Paid $86 for it. I believe that is the one...
1067
claygraner
Sep 10, 2002 10:11 pm
Is Honeywell part no. AMCC-630 the part that Bearden has used? http://www.metglas.com/downloads/powerlite.pdf Also what material seems to be the best of the...
1066
robert_bielik
Sep 8, 2002 8:44 pm
Thanks Norm, Seemed to me like a possibility to get rid of the back-EMF from the secondary to the primary in the MEG when switching the flux. And the best to...
1065
megaheadache
Sep 6, 2002 4:32 pm
... ( ... couple ... resistance ... like ... Very similar results here too Ken, I tried a 200k resistor and the best reading was 2.3Mohm Dennis...
1064
carbonprobe
Sep 6, 2002 1:20 am
... an ... red ... CRT..bound ... To Late, I tried it last weekend and it works great. I fried a couple of 120kOhm carbon resistors. The resistor reaches a...
1063
fletchmo47
Sep 5, 2002 5:26 pm
... Good Grief Man!!!! Don't do it you'll kill us all!!!!!! zzzzzzzzzzzzzzzzzzzzzaaaaaaaaaaaaaaaaaappppppppppppppppppp Norm...
1062
fletchmo47
Sep 5, 2002 5:26 pm
Steve I read nothing about a special resistor in the patent material either. Looks like the picture of the patent device has wire wound resistors to me too. ...
1061
Steve Williams
daemonphi
Sep 4, 2002 4:33 pm
Hello everyone. I have seen the occasional message recently from people embarking on their first attempts at replication. This requires alot of effort,...
1060
gewo
gewo@...
Sep 4, 2002 4:32 pm
http://www.geocities.com/nayado/ ... Odchozí zpráva pravděpodobně neobsahuje viry. ... "Never underestimate the power of human stupidity." ("Nikdy...
1059
fletchmo47
Sep 4, 2002 4:30 pm
... eq. which is that a magnetic field can be produced without current flowing in the wire. ... primary would not draw any power... or would it? ... Not a...
1058
fletchmo47
Sep 4, 2002 4:28 pm
Hello all I have acquired a very large Metglas core (AMCC-1000), a large 2x2x1.5 neodymium magnet and am on my fourth generation of a control switcher for the...
1057
BobW
rmwinchester
Sep 3, 2002 5:03 pm
Hi Ken et al Nice explanation of how to make a carbon film resistor. (Ken) The carbon resistor link that Bob found has 5 Watt "carbon film" resistors and 2...
1056
drspark86
Sep 3, 2002 1:39 pm
Hello All After further homework I have found that information in JLN's report and that found in Tom Bearden's Original paper megpaper.pdf, does not show the...
