Is anybody out there in MEG Land? My latest deep thoughts: The MEG can be considered a parallel LCR circuit. When an LCR circuit is in resonance the voltage is...
In a message dated 3/8/04 9:46:13 PM Eastern Standard Time, ... Ken, Yes, I agree, with limitations. Bear in mind that this only one form of earth resonance,...
Hello I am glad to see that MEG builders groups still live (excuse my poor english because this is not my natal language but french). I signed up your group...
Good Morning everybody I write this post to inform you my lasts results in experimenting my MEG (not really mine, a friend of me gave me it to test it). I...
All, In the message just previous to this one, Pascal Di Scala has shared his MEG experiment notes with us. Thank you Pascal!!! An impressive MEG! Please...
Hi Pascal, Thank you for sharing your nicely detailed work! In my MEG experimentation with MOV loads, I had experienced similar variations in the output/input...
Hello everybody I have continued my tests over the MEG and I have not yet succeeded in a COP greater than 1, it is less than 1, very less than 1. My las t ...
Hello Jon Thank you very much for your advices. I have done a measurement campaign on MEG inductances and resistor values (input and output coils), with the...
New application copies existing patent
The new application simply copies the verbiage of the existing
patent. What is different are the claims where the...
(I Corrected the bad link -Dave) All, Here are some links to photos in the files section of what appears to be a newer MEG by Bearden and co. which was...
All, Sorry about the bad links (so much for my trying to make things more convenient). Please just check the MEG pictures folder in the files section if...
All, I found the photos of Bearden's MEG2 placed on the site by Dave Narby to be very interesting. I have spent some time with the photo of the MEG looking...
Dave, Stan and All, Dave, thanks for posting the pix on this new MEG and thanks also to you Stan for the schematic. This unit does indeed appear to be...
Hi Jon/all, Please ignore the links I sent in the previous post. I was attempting to make it easier to see them by using a "link shortener", but it appears it...
The pictures of MEG-2 appear to show that the device is built on a core similar to the Honeywell AMCC-1000. The coil forms are now 3/16-inch plexiglas, which...
Hi all. From the new Meg pictures, some things are to my understanding quite important. a) The input coils are really, really thin. No more than the width of...
Hi All, I had now a closer look to the picture and thanks to the high resolution of it, one really can see a lot ! The input scope picture shows at the upper...
Sorry. I had again a closer look and now saw, that the RMS current of the input circuit is around 4.3 Amperes all the time. First I did not see the groundline...
I believe, that the new MEG-2 just uses a simple 74C14 hex inverter ( with schmitt trigger) http://www1.jaycar.com.au/images_uploaded/MM74C14.PDF or 4069 hex...
... from ... wondering ... symmetry of ... of the ... large ... correction must be ... output power ... Well, I tend to agree here Jon, but watch, that the...
All, Regarding the previous "Re: Analysis of the MEG-2 coils-core" posting from Overunity2001, it took me awhile to figure this message out because of the...
... I don't think so. The picture shows 4 wires going to the input coils. If you look very closely you can see a two position terminal block with 2 wires...
... coils. ... Hmm, well, yes, but maybe they have just connected the 2 input coils on the PCB together in series... This could also be... ... Hmm, I don´t...
Hi Stefan, ... Could be, new PIC doesn't use cristal and has 14 pins, more or less, pease see PIC 16C505 OTP - with internal clock it work at 4 MHz: ...
... Pará. All, FYI This message in Portuguese roughly translates to english as .... "Subject: Some contrutor (constructor?) of MEG in Brazil? I look for for...
Dear list members, Over the course of moderating this list, we have had to reject many posts due to the focused nature of this group. While some of them were...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
