Hi, At this very moment you can purchase the Metglas AMCC 320 cores for $110 from http://elnamagnetics.com There's some very important information MEG...
Wow Paul! Very good research! I am very impressed with what you have presented here. I might add that that one way to get them to dynamically change resonance...
Hi I wanted to give you some of the results of my MEG replication and the current state of my ongoing investigation. Some initial notes: 1. The MEG should not...
Hi all! I recently discovered one Bulgarian experimenter that built MEG like device with COP > 1. His Website is here: www.inkomp-delta.com. The site is in...
Hi All, I'm new group member. I have university education of radio electronics. Some days ago I made MEG Bearden's style. I use Metglas AMCC 1000 core and...
All of the reports I've heard have been COP < 1. However, Bearden said on his Energy from the Vacuum Part 1 that it will take no less than $9,000,000 to...
I found: Permanent magnet flip-flop: with possible with half gainer Searching for reversal: need to understand the cause - please help if you can I have...
... NOTE FROM MODERATOR Many of you may wonder why this message was approved for posting to MEG Builders when it is off topic. I approved it because the...
Vincent, I did some experiments with the "SMOT" magnetic ramp many years back and it called for very long and thin magnets. I was able to forcefully tape...
Vincent: Leedskilnin, the builder of Coral Castle wrote a book that might give you some insight into what is happening. In it he gives experiments that display...
What you describe is exactly what physics books have described for centuries. Any energy you could generate with this scheme would come out of the energy it...
Hi Vince, Could you describe your setup a bit more, I have the impression that: Your anvile is ferromagnetic (as opposed to say a brick)? Your magnets...
It is my belief that a magnetic field is effectively a moving mass, involving constant rotation of the ether from one pole to the other. So, these are my...
... Vince, Your posting has gotten a lot of potential answers to your question about magnet reversal and I hope that you find your answer within them. I...
US Patent # 5,221,892 discloses a permanent magnet generator which incorporates solid state flux control valves and a rotating field across inductive elements...
Considering that no one seems to be able to get any O/U from the MEG, maybe we should try to redesign it a bit. Bearden talked about barium in BaFe magnets...
Keep in mind that many of the original MEG experiments used materials like metglass OR orthonol that have a nearly othogonal hysterisis curve. These materials...
***** PREFACE BY GROUP MODERATOR ******* I am approving this posting with some trepidation that it might spur a round of THEORY discussion. What's the problem...
... LES, MY REPLIES ARE EMBEDDED IN ALL CAP TEXT WITHIN YOUR ORIGINAL MESSAGE BELOW. STAN MAYER <snip> ... PLEASE ELABORATE ON "CERTAIN CHANGES" AS I HAVE SEEN...
As a new group member, with a Metglas AMCC 320 core 1) With a plug in transformer (15.23 DC volts 1.5 amps) to the input board tuned to 12.43k we read.... 2)...
I haven't posted in a long time because not much has happened with my AMCC1000 core. After meeting Don Smith in 2007, it became a possibility that operation of...
Hi Congratulations for your work. If you could include a drawing with your data, it would be greatly appreciated. I notice time plays the same tricks on you as...
Group, Recently I had a phone conversation with a serious MEG experimenter who shared with me some information about the MEG core that apparently comes from a...
This is not necessarily new news to some people. If you really think the critical factor is the B/H curve then get a bunch of small strip wound toroidal cores...
I have a problem on the secondary leakage current I thought I put the tape (the black one) between a secondary winding and another to evid losses. I do not...
Dear MEG_Builders member, This message is to let you know that on Oct. 7, 2010 the Yahoo MEG_Builders group will be closed down. The reasons for this are many...
