Hi, I am looking for any help on disassembling this Nikon 70-300mm D AF lense, unfortunately the lens has developed heavy fungus on almost all elements of the...
Hello Avi, The following URL does have some digrams. Unfortunately not the one you need. Maybe it is possible to get some inspiration by the others ...
I just converted my D70 to InfraRed by removing the hot filter and replacing it with one I got from LifePixel.com. The conversion required the removal of the...
Tony: Although its a real pain, it might be worth disassembling the camera again to "retrace" your steps just to make sure that all the wires and ribbon cables...
Thanks for the comment. I have retraced everything a dozen times. I also wore a grounding strap so I don't think it is a static problem, but more a ribbon...
When reassembling everything, could there be any possibility of a ribbon cable or any cable/wire getting pinched? It happens all the time, wires get pinched...
Tony, it sounds like you've done all the right things. Not to sound like a broken record but some ribbon cables can be difficult to insert into the full depth...
In a message dated 1/6/2007 12:08:01 PM Eastern Standard Time, hypermodest@... writes: Interestingly, that rewinding and shutting going OK without this ...
... what I can ... top hat ... elongated slot) ... Yes, but when I cover it with lid, lever begun to move within some limits, I think. ... just need a ... hole...
I have the SB-14's but require some info for the SB-11 and do not have one at hand to make measurements on. Does anyone know what the xenon lamp discharge...
Hi, I recently bought a used FE-2, ser. no 2.201.xxx.xxx and surprisingly with a aluminum shutter. Is it common? But the camera has a small problem with the...
Hi Avi, I've put the parts diagram in the 'files'section. I just removed fungus from a 35-70/2.8 myself, here are a couple of things I learned: 1: Get a good...
Hi George, There is a page about a spotted sample like yours : http://www.mir.com.my/rb/photography/hardwares/classics/nikonfeseries/fe2/fe2alumi.htm (or just...
... Hi Karim, thanks a lot for the link to mir. I found the picture for the Aluminum shutter FE-2. Regarding the writing there is nothing special on the camera...
The replacement blades that Nikon has been supplying for many years are the flat aluminum type. It's quite possible that the original shutter blades were...
Howdy group. Just joined. Was given a Nikon FE recently. It hasn't been used in 15 years. I only have 6 mo experience with SLR and all of it on a new...
Rachel: It sounds like its simply locked up. Its likely not due to deteriorating foam unless the firror foam has gotten so sticky and gooey that its holding...
hi rachel, If the camera is jamming where the mirror will remain in the up position and will not complete the shutter tripping action, an out of sync condition...
Hi Rachel, As Perry said, the camera did not complete its cycle and is stuck mirror up. If the condition that caused the stop in the cycle is still present, ...
Hello, I bought a used FE off eBay (my third, I love the model), and at first I thought this one was mirrorless, but it was just stuck against the foam. A...
Kelly it seems that if the mirror is loose 99.9% chance that it was replaced at one time. the OE mirror is glued in and also held by 2 spring clips. From what...
Casper, ... on things i was looking for. Though this is not the exact lens i have ( i have one without macro), able to open half way through and had to put it...
Hi Kelly, I did not get if the mirror is loose from the mirror holder or if it's the mirror holder that is loose from the body... Lou understood it's the...
The focusing on the above lens has become jerky and in some instances refuses to focus anymore. This has happened since a screw came loose on the barrel...
Dear "brownd012092", I send you by email a paper I wrote about the AF 35-70 I dismount some month ago. I hope this helps, even if it's not the same type of...
Hello, Thank you both - the mirror seems seated in its clip, but the clip is loose from the side of the camera interior. I tried moving it a little to see if...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
