The rewind crank fell off my FM2n! :( Just the little lever, not the disc or anything else. I have the lever, it looks like the pin that holds it in place must...
In a message dated 10/2/2007 6:13:00 AM Eastern Daylight Time, adamburr1973@... writes: The rewind crank fell off my FM2n! :( Just the little lever, not...
hmm...i think the pressure plate is missing too. i looked under the disc (haven't removed it yet) and i don't see anything under there to keep the pin from ...
never mind, the plate is there. somehow it swung around to the side which is why the pin fell out i guess. sounds like i should be able to fix this myself,...
Hi folks, I have two books about the Nikon F3 for sale. This is because I bought an F3/T, then decided I didn't like it because of its electronics, so I bought...
In a message dated 10/2/2007 10:44:51 AM Eastern Daylight Time, adamburr1973@... writes: hmm...i think the pressure plate is missing too. i looked under...
thanx, I'll take a look Malcolm ... Hi, Don't know if u still need it, but I've posted an exploded view of the 50/1.8 in the 'files' section. Best regards &...
Hi, I need to get at the whole aperture blade area of my 16/2.8 AI-s. I can't seem to get there from the rear so assume I have to take off the front...
Thanks, William. I can see something like that on the European site for Micro Tools: "Spanner Wrench Wide (Imported)". So is that the best thing to use for...
Jason, Once you tighten the adjusting nuts, it's pretty solid and twist is minimal. It's much like using a screwdriver: You do have to apply constant force...
... Start here, MicroTools has eight pages of spanners. http://www.micro-tools.com/store/SearchByCategory.aspx?CategoryCode=SPN I use two different types on...
I have both of these lenses with different problems. The 3.5 has a classical problem, stiff focus. Seems the lubrication is just waxy due to age. I want to...
I was converting some non-AI lenses to AI. The hard part is removing the aperture ring. Some sample instructions for doing this are posted on the web: ...
Mark, that was very helpful. I was trying to convert my Nikkor-SC 50mm f/1.4 to AI and was not able to remove the screws. It damaged three of my philips screw...
Bijesh
bijesh.ks+groups@...
Oct 9, 2007 3:40 pm
7163
In a message dated 10/9/2007 10:46:09 AM Eastern Daylight Time, slowhands95128@... writes: Micro tools has them, but the quality is not quite as good as...
Thanks for the "tip" on JIS screwdrivers. Is there a special set of screwdrivers for slotted screw heads? I've seen screws which have narrower slots for their...
Brownells in Iowa/ USA carries special gun screw drivers w/ parallel side tips so you don't mess up the slotted screw head. They also sell a fixture that...
I am trying the handbook of service of zoom the Nikon Nikkor AF 35 70 2,8 or designs of the assembly outline. Who can help me, thanks. Cordial Maurizio....
... As far as I know, Sover is an F2 specialist and doesn't work on lenses or other cameras. He often posts here and monitors this list, so he may reply ...
Search the archives for the 55mm 2.8 - there was someone else with the same lens and issue. Cleaning the blades can be easy or not, depends how far you want to...
I used the same technique for my 28mm 2.8 AIS. Removed the ring at the back, then the three elements in the back fell out and I had access to the aperture...
Bijesh
bijesh.ks+groups@...
Oct 11, 2007 4:45 am
7171
Hey all, I'm hoping someone here can help with a stuck FE rewind knob... I was about to put in a fresh roll, and lifted the knob to open the back... It went...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
