I have oil/grease contamination problems with plastic parts for aluminium coating.(oil e.x: silicone or release agent that normally use for injection molding)...
Sutrisno Ishak
stibcm@...
May 2, 2004 6:21 pm
1056
Dear colleagues, the 12. Neues Dresdner Vakuumtechnisches Kolloquium (NDVaK) on "Coating and Moification of Plastics Surfaces" will take place on October...
drestransvak@...
May 4, 2004 2:03 am
1057
Dear Daphne, I am using 50 Ohm/m coax. cable in the frequency range 50 to 250 kHz for voltages up to 1000V/2A and in other application at 13 kHz and 3kV/1mA. ...
Good Morning, We had some very bad experiences in terms of system pump down with anodized Aluminum parts. We replaced them with parts that were not anodized...
Andrew Bass
abass@...
May 4, 2004 2:03 am
1059
Dear Sutrisno, Try using oil solvents, such as gasoline, acetone, izopropyl alcohol, etc., followed by ethyl alcohol bath, to avoid any solvent traces. We used...
Dear all. I'm having some dificulties in findings a company that can coat big mould parts withe PVD TiN or CrN in Europe. Our chamber as a limit of...
Prirev, Lda
prirev@...
May 5, 2004 10:52 pm
1061
Conventional lithography technology limits its scaling capability by the wave length of light used. The nanotechnology requires line size 100nm or less. The UV...
Dear Mr Santos, You could contact the following companies: Metaplas Ionon Oberflachentechnik, J.Vetter, Bergisch-Gladbach, Germany (phone +49 2204 299 261) ...
Michael Stuber
michael.stueber@...
May 6, 2004 11:50 am
1063
Try Hauzer in Venlo, The Netherlands. I remember seeing a picture of a TiN coated food mixer that was about 2m long which they coated. Also, I think PVT in...
Dear Pirev, Try Bodycote in Venlo, The Netherlands (+31-77-3559222). They have several really big machines that would fit your mould size. Best Regards, ...
Christian Strondl
cstrondl@...
May 6, 2004 11:52 am
1065
Dear Pedro Santos, We have in Italy a PVD equipment with dimension of 2000 x 900 x 900 mm where it's possible to coat large moulds with TiN, TiCN, CrN. To...
Franco Rabezzana
metec@...
May 6, 2004 11:53 am
1066
Dear Pedro, Try the following UK company : Tecvac Ltd Buckingway Business Park Swavesey Cambridge CB4 5UG Tel (0)1954 233700 Fax (0)1954 233733 Dr Jonathan...
Dear Pedro, please contact company Metaplas Ionon, Am Bötcherberg 30-38, D-51427 Bergisch Gladbach, Germany (Dr. Jörg Vetter, r-and-d@..., phone...
Schultrich, Bernd
Bernd.Schultrich@...
May 6, 2004 11:54 am
1068
Does anyone know of equipment suppliers or coating service suppliers that provide thick coatings (0.25 inch)? The preference is to be deposited by EB-PVD, but...
Klingenberg, Melissa L
klingenb@...
May 8, 2004 2:46 pm
1069
Hi Melissa, I would try the suppliers of thermal barrier coatings. In Kiev there is the world famous Paton Welding Institute. They make EB guns. See, for...
Antti S Korhonen
asko@...
May 8, 2004 5:23 pm
1070
thermal barrier coating can be done by coating refractories on pipes our company does these coatings if interested pls let me know the method is hydraulic...
Sunil Gupta
nelsg@...
May 10, 2004 10:50 am
1071
Melissa, There is a company in Florida called Rohwedder that has built about a dozen EB-PVD systems for a US engine builder to deposit thermal barrier coatings...
Hi Melissa, In the US,Telemark is now the major supplier of E Beam systems. Dale [Non-text portions of this message have been removed]...
dmorton@...
May 10, 2004 10:51 am
1073
MAY I REMIND YOU THAT MAY 15 IS DEAD LINE TO SEND ABSTRACTS? Dear Colleague, ASEVA member and ASEVA sympathizing This announcement is to remind you the...
Jose L. de Segovia
jldesegovia@...
May 10, 2004 10:51 am
1074
Dear Melissa, Paul, BOC Temescal is still the big name in PVD systems and EB guns, providing high evapration rates and thick layers for all kind of...
David Schijve / A. de...
davidschijve@...
May 10, 2004 10:54 am
1075
Dear Melissa, Some remarks to your question. Coating thicknes of about 0.25 inch, it is really needed? It is quite high thickness for a PVD coating process....
Hello Melissa, VON ARDENNE is a supplier of ebeam guns for primary metal processing, and ebeam coating systems for high rate deposition of TBC and metallic...
Mark Pellman
mark.pellman@...
May 10, 2004 2:48 pm
1077
Dear Sunil, Thank you for your response, but we really weren't looking for TBCs. We are just looking for high rate EB-PVD suppliers for that particular...
Klingenberg, Melissa L
klingenb@...
May 10, 2004 2:49 pm
1078
Hi Melissa, If you are interested in coating complex geometry parts, Deposition Sciences, Inc. in Santa Rosa has a Low Pressure Chemical Vapor Deposition ...
gibbonskp@...
May 10, 2004 5:29 pm
1079
Helo Everybody I am curious if there are any sites that advertise/post PVD jobs, particularly for industrial positions? I am little surprised but can not find...
B.V.Rao
bvrao1@...
May 11, 2004 5:21 pm
1080
Look under III-V and II-VI compounds, LED and related devices. http://groups.yahoo.com/group/PVD_coatings Group Moderator: Vasco Teixeira (Univ. Minho)...
Ajay P. Malshe
apm2@...
May 12, 2004 11:12 am
1081
Try http://www.svc.org/ or http://www.vacuumresources.com/. There are a few listings, but the job market is pretty tight....
John German
jgconsulting@...
May 12, 2004 11:16 am
1082
Hello Group, I have a customer who wants to sputter from a pure tin target and reactively deposit SnO2, with addition of oxygen gas (which optionally could be...
Can't say as I've run into a serious contamination problem with Sn "poisoning" a system but the raw metal does getter and does have a fairly high vapour...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
