Dear all To deposit TiB2 from a TiB2 target does I need any working gas besides argon? I think this target is electrical conductive so I may use only DC power...
Ar if fine by itself but if harder film is required, use some nitrogen. It is electrically conductive and DC is easier in my opinion. Regular vacuum pumps...
Dear Bill, I suggest Niobium oxyde/hidrate,since it was testing with succes by Don Flowers at GENTEC (USA). Prof. Luiz de Miranda Federal University of Rio de...
Luiz Roberto Martins ...
miranda@...
Jan 5, 2005 2:50 pm
1501
Dear Paulo, I have a lot of experience in sputtering TiB2 from a TiB2 target, you just have to use Ar, but depending on the Ar-pressure and target-substrate ...
CALL FOR PAPERS Symposium of Nanodevices & anofabrication International Conference on Materials for Advanced Technologies (ICMAT 2005) 3 ~ 8 July 2005,...
Zhang Qing (Assoc Prof)
eqzhang@...
Jan 6, 2005 11:31 pm
1503
Dear all, Can somebody recommend an equipment manufactory for sputtering, the technical specs. should be better than Perkin Elmer machine model 2400 with three...
CALL FOR PAPERS Symposium K on "SiC and Related Materials" International Conference on Materials for Advanced Technologies (ICMAT 2005) 3 ~ 8 July 2005,...
Rusli (Assoc Prof)
erusli@...
Jan 8, 2005 12:29 am
1505
Dear Jun, I strongly recommend the Teer Coatings Ltd.'s UDP Systems. I have already used the UDP 550/4 system since 1997. I have no any problem with it. You...
Ihsan Efeoglu
iefeoglu@...
Jan 8, 2005 12:30 am
1506
PLEASE CALL GALCO ELECTRONICS INC. 972-222-8484 REFURBISH AND MANUFACTURE NEW AND USED COATING EQUIPMENT [Non-text portions of this message have been removed]...
Galco123@...
Jan 8, 2005 12:32 am
1507
Dear Mr. Xiao, Please, visit our Web site at www.mac-co.8m.com to have more info regarding our technical solutions. My company can deliver you customer...
Dear Jun Xiao, Our company manfactures vacuum coating systems for a wide variety of applications, and would be able to provide the system you require. I am not...
Dear Jun: Torr International manufactures Sputtering Systems with multiple guns, 2" targets or larger, DC, and/or RF, substrate ...
masud.naraghi@...
Jan 8, 2005 12:34 am
1511
Dear Jun, Sigma Technologies has a lot of expertise in building high quality, high yield sputtering machines. Please check our web site www.sigmalabs.com to ...
ali boufelfel
boufelfel@...
Jan 8, 2005 12:34 am
1512
Dear Colleagues, Happy New Year to All of You. I have joined the PVD group last year and am pleased to receive information related to the subject. However, as...
Török Tamás
fektt@...
Jan 10, 2005 11:55 pm
1513
Dear Colleagues, I would like to remind that if you have not already submitted your abstracts for the International Conference on Surfaces, Coatings and...
Dear Dr.habil Tamás I. TÖRÖK Check out the following article If you have aceess to the journal. If not mail me I can send you a copy. Chemical vapour...
Dear colleagues, I am currently working on producing a Iridescent finish on brass fittings with a Cu,Ni,Cr decorative finish. I am using 100cc Ar and 100cc...
You need to produce varying thicknesses of a clear ZO2 top layer to shift the visible color. Gary Vergason...
Gary Vergason
gvergason@...
Jan 12, 2005 3:04 pm
1517
Dear Colleagues, I'm performing DLC depositions using a RF PECVD system designed and bulit by my company. DLC coatings are made on stainless steel but I'm...
Dear Simon, Further to your enquiry it is difficult to obtain good adhesion between DLC and stainless steel unless very high energies are used with an rf...
Dowling Denis
Denis.Dowling@...
Jan 14, 2005 8:10 am
1519
Dear colleagues, we have to heat up cristalline silicon close to the melting point in contact with a graphite heater. Is there any suggestion about an...
Reinhard Günzel
r.guenzel@...
Jan 14, 2005 8:10 am
1520
Mr. Mutti, In my experience with DLC the best adhesion was achieved by using alumina as bond interface layer. You can find more detailes in my paper: N....
vigase@...
Jan 14, 2005 8:12 am
1521
Dear Simone Pre-coating sputtering cleaning might solve your problem. Some years ago I used pre-coating sputtering and deposited DLC on WC with excellent ...
Sam Zhang Shanyong (A...
MSYZhang@...
Jan 14, 2005 8:12 am
1522
Dear Simone, If your stainless steel is cleaned well, and sputter etched before the Ti deposition, you should be able to obtain fairly good adhesion. We use...
Hello Reinhard, You may not need a coating at all--I believe that at the melting point of silicon the diffusivities of Si and C in SiC are very low, so the...
Dear all, I have designed a new website with more information about the theory of PVD coatings. The website URL is http://www.pvd-coatings.co.uk The...
Jarratt Mark
jarrattmark@...
Jan 15, 2005 9:38 pm
1525
... Exhibition ... French ... anniversary of the ... on Monday ... to invite ... 2005....
Dear colleague, We are pleased to inform you that preparation for the workshop "New opportunities in Material Science: from Nano Objects to Complex Materials" ...
María Dávila
mdavila@...
Jan 16, 2005 11:59 pm
1527
Dear Simone, Mr. Doll suggestion is perfect. If you grade an interface layer from pure Ti to pure DLC with thickness in the range 200 to 300 nm, you will have...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
