... From: Sam Zhang Shanyong (Assoc Prof) Cc: Sam Zhang Shanyong (Assoc Prof) Sent: Friday, March 31, 2006 3:36 AM Subject: ThinFilms2006: 2nd Call for Papers ...
Vasco Teixeira
vasco@...
Apr 3, 2006 12:00 pm
2979
Mark your calendar----- Original Message ----- From: AVILA Jose To: vasco@... Sent: Thursday, March 30, 2006 6:38 PM Subject: Synchrotron...
Vasco Teixeira
vasco@...
Apr 3, 2006 12:01 pm
2980
... From: sfv To: vasco Sent: Friday, March 31, 2006 2:14 PM Subject: 4e Journées d'Etude sur les Nouvelles Tendances en Procédés Magnétron et Arc pour le...
Vasco Teixeira
vasco@...
Apr 3, 2006 12:01 pm
2981
... From: <tco2006@...> To: <tco2006@...> Sent: Thursday, March 30, 2006 9:11 PM Subject: IS-TCOs Crete, Greece...
Vasco Teixeira
vasco@...
Apr 3, 2006 12:01 pm
2982
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the PVD_coatings group. File :...
PVD_coatings@yahoogro...
Apr 3, 2006 12:02 pm
2983
hi all, What kind of Graphit material we have to use for making EB evaporation Liner? best regards, N. Sobhkhiz...
Nader Sobhkhiz
sobhkhizy@...
Apr 4, 2006 2:12 pm
2984
... -- ____________________________________ Donald M. Mattox Technical Director Society of Vacuum Coaters 71 Pinon Hill Place NE Albuquerque, NM 87122-1914 ...
SVC
donmattox@...
Apr 4, 2006 6:48 pm
2985
Yes, the most common crucible materials are pyrolytic graphite. The link below is for Poco Graphites web page that outlines the general sizes for crucibles. ...
George Wityak
gwityak@...
Apr 7, 2006 11:20 am
2986
Dear Colleagues Currently, we are organizing the inaugural number of IJSurfSE (International Journal of Surface Science and Engineering). We acknowledge your ...
Vasco Teixeira
vasco@...
Apr 7, 2006 11:23 am
2987
Hello everyone, We are having a Leybold L-560 plant with ESV6 e.beam evaporator and one thermal source, IR heating. It has a Turbovac 1000 TMP. Oxygen is given...
VI-th International Conference on Ion Implantation and Other Applications of Ions and Electrons ION 2006 in Kazimierz Dolny, to be held from June 26 to June...
Vasco Teixeira
vasco@...
Apr 7, 2006 11:34 am
2989
Hi, We are very familiar with the Leybold560 system and would rather recommend a gridless end-hall ion source for this job. The EH400F ion source by...
Dear Hermang, An ion source is almost always a potential improvement if properly applied. However, it might not solve your problems. When you say "shifting",...
Ron Willey
rwilley@...
Apr 10, 2006 12:55 pm
2991
...  ______________________________________________ Orlando M.N.D. Teodoro Professor Associado CEFITEC— Centro de FÃsica e Investigação Tecnológica ...
Orlando Teodoro
odt@...
Apr 10, 2006 12:56 pm
2992
Hello everyone. I'm working with some of the local grad students on my sabbatical here at the Royal Melbourne Institute of Technology in Melbourne, Victoria, ...
Dear Hemang Jesrani, You wrote: "Substrates are normaly heated to 270° (this is the temperature at which the controller is set but the temperature on the...
Hi, An Ion gun will not improve process control-by itself. If you are having wavelength and index repeatability problems, this won't solve them. Without...
Dear Jim, as I see from your report on the problems with aluminium deposition, you are perfectly aware of possible reasons of observed instabilities. The only...
Gulbinski
gulbinsk@...
Apr 10, 2006 3:12 pm
2997
Dear Sir, You may want to check the magnets of the magnetron if DC discharge can only be maintained at higher pressure. Good luck, Yuan-Min Li RESI (Renewable...
Yuan-Min Li
yuanminli@...
Apr 10, 2006 3:12 pm
2998
Hello everyone, This seems a familiar problem. It is acting like there are no magnets. It is also possible that the magnetic return path is not simply between...
larry.anderson@...
Apr 10, 2006 3:15 pm
2999
Jim, It sound like your set up is adequate, except that you'll want ot run at a much lower pressure. 3 to 5mT is suggested. At first, the surface will have ...
Hello, I would like to know little bit about, what happens exactly after you switch on the DC power supply. Kindly let me know about the DC power supply,...
Hi If the Aluminum target is not pure (I assume you are working with a pure target) then you will end up with this problem, because of the oxidation of the...
Dear PVD coatings group, Thanks to all (especially Larry, Yuan-Min, Witold, John, and Stan) for helping me diagnose this problem. It does appear to be the ...
Hello James, As others mentioned, check the magnet array, but firstly check the power cable. At mentioned pressures (80 - 100 mTorr) the plasma must glow even ...
Dear James, We at Milko Angelov Consulting Co Ltd. can make retrofit of the magnet array of your 4" cathode. We use NdFeB magnets and usually make unbalanced...
Hello All, I am looking for a PECVD system for depositing Si nano-crystals onto a 3 or 4" wafer. Can you guys recommend/comment on vendors who have expertise...
Venkat Bommisetty
bvrao1@...
Apr 12, 2006 10:10 pm
3006
Dear Jim, regarding magnets, you could contact Dr Witold Posadowski from Wroclaw University of Technology (PL). We usually use his magnets in our magnetron...
Gulbinski
gulbinsk@...
Apr 12, 2006 10:10 pm
3007
Magnet Sales http://www.magnetsales.com/ Dexter Magnetics http://www.dextermag.com/Page63.aspx Are two reliable companies. If you have a drawing of the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
