... -- ____________________________________ Donald M. Mattox Technical Director Society of Vacuum Coaters 71 Pinon Hill Place NE Albuquerque, NM 87122-1914 ...
SVC
donmattox@...
Aug 1, 2003 10:30 am
455
Gary, What alloy is the PM? If you have an alloy material you should bake it out at 600 F then blast with silicon carbide fine grain. It may not be practical ...
Ray
RMonahan@...
Aug 1, 2003 10:30 am
456
We have used TIB2 on this application. You need to apply a thin nickel plating first. Then use TIN and TIB2 ... From: "Prirev, Lda" <prirev@...> To:...
Ray
RMonahan@...
Aug 1, 2003 10:31 am
457
We have depositied Ti, TiO2, and TiN on a variety of materials including polymers, glass, metals, carbide tool material, etc. using VAD and FVAD (vacuum arc...
Dear Pedro Santos, If you mean Al deposition onto polyurethane, we may think about. For us magnetron sputtering of Cu and Ni onto polyurethane tape is usual...
Vitali Verigin
coatinfo@...
Aug 1, 2003 10:33 am
461
Dear All Is it possible to establish a temperature to be considered safe to resume a process in case of a system shutdown? I'm coating CrN by cathodic arc at...
ricardo.camasao@...
Aug 1, 2003 10:36 am
462
Dear Ricardo It depends on whether you are prepared to accept a visible interface within the coating. We have done some work in this area for process quality...
Peter W. Hatto
p.hatto@...
Aug 1, 2003 11:05 am
463
Dear Ricardo, dear all I agree with Peter concerning the quality of the interfaces with a set value for deposition temperature. It will depend in coating...
Vasco Teixeira
vasco@...
Aug 1, 2003 1:46 pm
464
Dear Ricardo, Dear All For safety reasons you should always do a Glow discharge from 500 to 800V prior to restart a cycle but be sure that you do not open the...
Prirev, Lda
prirev@...
Aug 1, 2003 4:44 pm
465
In this matter we do not open the chamber while the pieces temperature is more than 180șC Best Regards Pedro ... From: "Vasco Teixeira"...
Prirev, Lda
prirev@...
Aug 1, 2003 4:44 pm
466
Greetings, I have been involved in successfully depositing Ti and other metals on fabrics using roll to roll DC magnetron sputtering. One issue is the type of...
Dear All, We can sputter HA at a rate of 0.5-1 um/h and we'd like to cover now some titanium implants (slices, screws, or other shapes)and to test them in...
constantin morosanu
cosmorosanu@...
Aug 3, 2003 11:05 pm
468
Ti coatings on porus or fabrics can be coated by ebeam,without excess heat. In order to get penetration of fibers, use an argon background and deposit ti at 2x...
Galco123@...
Aug 4, 2003 3:31 pm
469
Hi, I am looking for someone with the capability to coat FTO onto glass substates to a resistance of 10-15 ohms\square and a transmission of greater than 80%....
David Corr
david.corr@...
Aug 4, 2003 3:32 pm
470
We can do it. It is necessary to use FTO ? What about for example ZnO doped with Ga. The optical and electrical properties are much better. Best regards ...
Elvira Fortunato
emf@...
Aug 4, 2003 3:39 pm
471
Dear All, I am interested in optical coatings. First of all can someone recommend good literature (book) ? Second are there coatings which selectively transmit...
Roger Theunissen
rtcenp@...
Aug 4, 2003 11:29 pm
472
Dear Gary, In principle, we have the capability to PV Deposition of various compounds at a production scale (both at our metallization center in Riga and ...
Vitali Verigin
coatinfo@...
Aug 6, 2003 2:20 pm
473
Dear Dr. Hatto, dear all Let me thank you for the answers, one of them caught my attention on other issue; "...there is no alternative but to strip the...
ricardo.camasao@...
Aug 6, 2003 2:24 pm
474
If you are looking for a guide to optical design the two books "Thin Film Optical Filters" by Angus Macleod and "Design of Optical Interference Coatings" by...
Mueller, Arnd
arnd.mueller@...
Aug 6, 2003 2:27 pm
475
Hello Gary, We are direct manufacturer of Zirconium Carbide in China. Can you please let us know the detailed SPEC, QUNT, Size of Zirconium Carbide you need? I...
SpecialMetal
chinesemetal@...
Aug 6, 2003 2:27 pm
476
Dear Roger, The classic book is Sh.A.Furman, A.V.Tikhonravov "Basics of Optics of Multilayer Systems" Editions Frontieres B.P.33 91192 Gif-Sur-Yvette Cedex - ...
VecoR Info
info@...
Aug 6, 2003 2:29 pm
477
Message from SVC - Society of Vacuum Coaters Announcing the 47th Annual SVC Technical Conference and Smart Materials Symposium Adam's Mark Dallas Hotel, Dallas...
You have received good advice on literature resources for designing these coatings. It is also correct that your requirements need to be better defined....
dmorton@...
Aug 6, 2003 8:54 pm
479
Thank you Vitali. I was talking about depositing the PVD layer in the mould that is going to work with polyurethane. To prevent the polyurethane to stick to...
Prirev, Lda
prirev@...
Aug 11, 2003 2:56 pm
480
Dear all, Can someone send me an optical microstructure of TiC and WC? or can tell me where I can find it? Best regards, Paulo Venâncio...
Paulo Venancio
venanciopaulo@...
Aug 11, 2003 2:56 pm
481
Dear Sirs Who know the size of Al target type ARQ900? Thanks http://groups.yahoo.com/group/PVD_coatings Group Moderator: Vasco Teixeira (Univ. Minho)...
Sorry Ricardo... Do You want to Know how to strip CrN? If yes just say so and I can help you... It's an easy (but carefull) electrochemical operation! Best...
Prirev, Lda
prirev@...
Aug 11, 2003 3:02 pm
483
Dear All May I know which company offers a good yet cheap calo wear test machine? Thanks X.T. Zeng Senior Scientist SIMTech/Singapore ...
Zeng Xianting, Dr
xzeng@...
Aug 11, 2003 3:05 pm
484
Dear Mr. Zeng, I suggest to get in touch with Dr. Willich from Fraunhofer IST in Germany. Best regards Bernd Szyszka ... Dr. Bernd Szyszka Head of Department...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
