Estimados colegas He adquirido un monocromador Oriel MS257™ 1/4 m Monochromator and Imaging Spectrograph. Con el mismo pretendo investigar las propiedades ...
Dear Saleh You can find lots of information in major glass world suppliers. For example, if you take a look at Pilkington.com website you find many details and...
Dear Colleague, We are trying to deposit titanium films on stainless steel (SS) substrates by magnetron sputtering technique. We would appreciate receiving...
Dear Gadkari, You need to make next steps for good adhesion: 1. Degreasing of the detail. 2. After pumping - glow discharge cleaning in Ar for few minutes. 3....
Dear fiend the first step is degreasing with use of suitable acid solution. teh second id washing with aseton or IPA. and finally use of dry air. it is very...
We need more information regarding the chamber configuration and power supplies used for sputtering. However a generic procedure would be: Clean SS surface...
Dear Friend Normally, there is no deference between Mic. Slide and Float glass.(Slides was made from float glass with thickness around 0.5mm) an example for...
Dear Friends, We are planning to prepare nanostructured solar cell. Please inform the suitable method for preparation. With kind regards, Yours sincerely, ...
Dear Colleagues, Due to a large number of requests the deadline for abstract submissions for the 3rd Internationjal Conference on Surfaces, Coatings and...
Nasar Ali
n.ali@...
Jun 6, 2008 2:19 pm
4689
Dear Friends I have a problem with cleaning of Organic Glass. conventional method such as Ultrasonic cleaning cause damage (Scratch, ...) on them, and washing...
Float glass can be different from microscope slides. Float glass is not even the same on both sides. The side that is against the molten tin is tin rich and is...
CHARLES BISHOP
cabuk8@...
Jun 7, 2008 5:22 pm
4691
In addition to the comments from Charles Bishop, you should be aware that maybe your float glass is precoated in one side with a Silica thin layer. Regards ...
Float glass is made by pouring molten glass on a molten tin bed. When it comes off the line it is coated on one side by tin oxide. The tin oxide is usually...
SVC
donmattox@...
Jun 8, 2008 2:27 pm
4693
The reports on the properties of float glass is authentic, and, after coating acres of float glass into first surface mirrors we can vouch for this. Some of...
Howdy Regarding the bottom side of the float line ("tin side"); I believe that much of the tin has actually diffused into the glass surface. This is covered...
Bob Anglemier
banglemier@...
Jun 9, 2008 3:39 pm
4695
All, I am looking at the difference of deposition rate between cathodic arc and magnetron sputtering. I know generically cathodic arc deposition is faster...
1st EUROPEAN SCHOOL ON ELLIPSOMETRY 21–25 September 2008, Bari, Italy From Fundamentals to Applications in Nanoscience and Nanotechnology Everything You Need...
Hello Henry, The deposition rate of unfiltered cathodic arc is usually 3 to 10 times higher in comparison with the magnetron sputtering, depending on the...
Hi, Applied MicroStructures, Inc. has an immediate opening for a Process Engineer at our headquarters in San Jose, CA. One of the primary job functions will be...
I work in the field of advanced packaging with PVD systems and have recently heard of the ULVAC SRH Series PVD systems but have no experience with the system....
Salaamon alaykom Hello I had a question about "adhesion of CdTe to Si and BK7 substrate". but i didnt receive any answer for it. I deposite...
Milko, Thanks a lot for your insight. Could you please give me some referenc papers about this? Henry ... From: Milko Angelov <milko.angelov@...> To:...
All, We have device physicist and process engineer position in crystalline silicon solar cells at Adventsolar. Please send your resume if you are interested. ...
Prabhat Kumar
pkumar@...
Jun 10, 2008 3:00 pm
4704
Hello Henry, I am sorry, I extracted these data from a lot of papers during my 20 years of experience in the field of magnetron sputtering and cathodic arc ...
Arcomac's large area filtered arc deposition (LAFAD) technology has demonstrated extremely high deposition rates: Consider this: just one LAFAD dual arc metal...
vigase@...
Jun 11, 2008 9:20 pm
4706
Practical Design and Production of Optical Thin Films (Sep. 8-12) in Alsenau, Germany. This course is intended to be valuable for new coating engineers and...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
