Dear Valentin, It is our pleasure to know you are sourcing LaB6 sputtering target, we are able to supply it. At present Cathay Advanced Materials Limited is...
CATHAY ADVANCED MATER...
cachem97@...
Feb 2, 2004 11:17 am
852
Dear Grazie The lowest sheet resistance you can achieve at that thickness can be less than 10-15 ohms per square or may be less, I cannot give you the exact...
Dear Signore Taglioni, In regard to your inquiry for ITO target suppliers, the ITO target market is generally segregated by quality requirements. Applications...
Dear Colleagues, As previously mentionned, we are pleased to inform you that our Web pages with information on the 4th International Chromium Colloquium (and...
Patrick Benaben
benaben@...
Feb 2, 2004 11:26 am
855
Gianni, 1500nm is a very thick coating for any optical function. On glass, we would expect that to give a resistivity of around 1 ohm /sq - possibly less. At ...
We are sputtering an aluminum film on acrylic sheet. So far the adhesion is not very good. Does anybody have experience getting an aluminum film to stick to...
Greetings, I am looking for sources of conductive antimony tin oxide deposited on glass. I would prefer a North American source if possible. Best regards, Dr....
I have had good experience with getting aluminum oxide to stick to acrylic. Then if you transition to aluminum metal, I think it would stick fine to the ...
John A potential problem may be acrylic sheet produced with resin that has poor low molecular distribution, leading to high content of low molecular weight...
Angelo Yializis
ayializis@...
Feb 4, 2004 10:05 am
860
John, I can't seem to log on to Yahoo, so I've responded by e-mail. I hope my points aren't too generic, but as you may know, or at least are now finding out,...
aknoll@...
Feb 4, 2004 10:06 am
861
Morning John, In a former life, I sputtered various metals and dielectrics onto acrylic, but never achieved an acceptable level of adhesion without the...
Hi John, perhaps you could try a couple of monolayers PCVD(HMDSO + O2) precoating, O2 flow optimum to be determined. May be a possible weak interface layer can...
Geisler, Michael (AF ...
mgeisler@...
Feb 4, 2004 10:09 am
863
Dear John, Try to use dynamic recoil mixing in the first phase of deposition. Sputter an aluminum target with a broad argon ion beam while the deposited ...
BELLO Igor
apibello@...
Feb 4, 2004 10:09 am
864
Dear John, the Fraunhofer IST ist able to provide SnO2:Sb films (as well as other TCO and optical films) by magnetron sputtering on area up to 100 x 60 cm2. At...
Szyszka, Bernd, Dr.
szyszka@...
Feb 4, 2004 10:10 am
865
Thomas, we have performed sputtering of metallic Ca (PK500 cathode, voltage about 350 V). There are two problems: the relatively poor quality of commercial Ca...
Hello John, Indeed, it is difficult to achieve good adhesion to the acrylic sheet. I think, that there is no need to use presputered Cr or Ti films. Try ...
My only experience with aluminum on acrylic has been with filament evaporation. I have had good luck with extruded acrylic (two different material suppliers)...
John, The suggestion by Dave Baldwin is something I use to do with Cr-oxide to Cr on plastics. The technique worked on acrylic,if I recall. If Al2O3 doesn't...
Forgette, Jeff
JEFFF@...
Feb 6, 2004 2:54 pm
869
Dear receiver of the PVD-Coatingsgroup, To introduce myself shortly. I am working as a consultant on surface technology. On this behalf I am working on several...
RTC&P Consultancy & P...
rtcenp@...
Feb 6, 2004 3:15 pm
870
Are you doing any type of pre treatent like an RF etch at low power. Typically on plastics there is a lot of junk, mold releases, additives ETC. Also heat...
Gagnon, Paul E
gagnonpe@...
Feb 7, 2004 4:09 pm
871
Anyone have a niobium sputter target and can sputter niobium metal? I am seeking to refer a customer to a lab with this capability for paid coating service. I...
I was wondering if there is anyone who could flow coat a few sample pieces for me. I have a couple of brake light housings that we need flow coated so we can...
Chad Brooks
c_brooks@...
Feb 7, 2004 4:13 pm
873
I am looking for a 40 kilowatt VRT transformer. 480 input; 4k amp @ 10 volts output. I need this for an old Stokes metallizer. please contact me at...
Chad Brooks
c_brooks@...
Feb 7, 2004 4:15 pm
874
dear Dave, ECOPROTEC, a brazilian company, has developed a Niobium Technology to coat niobium oxide by thermal aspersion. I´m professor of Federal University...
Luiz Roberto Martins ...
miranda@...
Feb 8, 2004 8:56 pm
875
Paul, yes we do plasma pre treatment by use of microwave excited radicals from a remote radical generator. The radicals do isotropic etching for removal of...
Gerd Walther
gerd.walther@...
Feb 8, 2004 9:07 pm
876
Greetings, There is no great secret. Acrylic can be metalized (up to 1000 angstroms) after pretreating with plasma etch and HMDSO with traditional rapid cycle...
Gary Vergason
gvergason@...
Feb 8, 2004 9:07 pm
877
Dear Mr. Taglioni, best ITO properties can be performed by sputtering an ceramic ITO 90/10 target. The substrate temperature during ITO deposition should be...
Struempfel, Johannes
Struempfel.johannes@...
Feb 9, 2004 11:31 am
878
I am interested in identifying sources capable of providing EBPVD zirconia coatings on turbine blades. Please contact me at rctucker@.... R. C. Tucker,...
Rctucker@...
Feb 9, 2004 11:31 am
879
Dear Dave Baldwin We have a small pre production sputter unit we also have a niobium target we can coat 16 samples at a time. Can you give me more details...
Dear Dave, We do have Nb sputter target and can provide Nb metal coating as well as Nb oxide coating using a vertical inline sputtering machine. What would...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
