... Louis I just did a quick test to see exactly what the overlap figure does to the numbers. (You probably know that you can open the .quad files that are...
... Howard, It is true that the light inks are at 0 at 100% when overlap is set to 0, but they start coming in right after that. It seems to be just enough to...
Hallo I am on WIN XP, QTR 2.5.2.0 and I am printing on a 4800 using Piezo K7 inks from a 13" roll. My problem is the waste of paper with each print. The 4800...
I'll take a look at the problem with my set up when I get back to the studio next week if nobody speaks up. My guess would be to look at the default setting in...
The main thing to check is that the selection on the printer itself agrees with the selection in QTRgui. They both should say Roll Paper for it to work...
Well the R2400 doesn't have a front panel to select roll paper feed. But it is also important that the selection in QTRgui matches where you put the paper i.e....
Hi Frank, If you have the profiles on the PC they are easy to move to the Mac. Just put them into a folder on the Mac, then drag an install script i.e. ...
... Lou, Where do you limit black ink itself, right at the point where no density increase happens or do you go a bit higher where the extra ink shouldn't add...
I take my roll down to Kinkos (they all have large 36" + paper cutters) and I spend an hour or so cutting stock for all the sizes that I commonly use. Dr....
Hi Ernst. ... When I was using the typcal QTR controls, I found I got better profiles using a slightly lower default ink limit. I would typically select an...
Hallo everybody I have tried the following remedies: 1. To select the roll feed with automatic cutter on in the printer display and in QTR. 2. To select the...
Hi Juraj, (1) should be all that is necessary. Are you using custom page sizes? Could you have the width & length reversed? Width is across the paper as it...
Hi everyone, I'm in the process of linearizing QTR curves per the Eye-One- ReadMe.pdf found in the QTR Eye-One folder. So far I have been able to create a .txt...
Hello as a new commer to the group and an user of qtr. I got a question I am using a 2400 with matt black installed, I use MIS K4 inkset with their Eboni matt...
Just joined the group tonight too see what's up with borderless printing in QTR...and here I find my answers. But, with my Epson 1280 loaded with UT2, I can...
Has anyone seen this? The drops are tear drop shaped, due to the movement of the paper, probably 1/16th inch in size. I was printing in ABW on Moab Colorado...
Hi Roy Thank you for your fast responses!! I am printing on a 13" roll in portrait orientation. My paper size is custom: width = 13" (the whole width of the...
Juraj, There have been posts on other list mentioning a problem with the CS3 upgrade that is causing a problem with roll paper. I am headed in to the studio...
Juraj, I just printed an image with my 4800 with roll cutter on. It drew the paper back in just like it should both with CS3 direct and through QTR. I used a...
Hi Juraj, It sure sounds like you are doing the right thing. I think the best thing is to get some specific details. 1) Get a screen capture of the QTRgui page...
Roy or Steve, I have been having issue with QTR getting locked out of the spooler by Adobe. I used PS to make a print with the 2200 after using the 4800. I get...
After I installed Leopard on my G5 none of my printers worked. While I could add them to the printer list in System Preferences, when I went to print the...
After rebooting the system and starting QTR first, it printed to the 2200 straight away. I suspect CS3 and it having a hold on the drivers. I have not deleted...
After rebooting the system and starting QTR first, it printed to the 2200 straight away. I suspect CS3 and it having a hold on the drivers. I have not deleted...
I have an R1800 and just installed an Epson 3800 and have similar problems switching between printers. My solution is to set the printer, close the print...
Hi Eric, I've read your descriptions and I'm trying to see where things are going wrong. When you say "locked" out do you mean hangs and waits or it gives an...
_____ From: QuadtoneRIP@yahoogroups.com [mailto:QuadtoneRIP@yahoogroups.com] On Behalf Of Roy Harrington Sent: Monday, December 03, 2007 11:21 PM To:...
I promised to provide some feedback on building QTR profiles using the "Plot List" feature, where you can design your own curves. Paul Roark has been doing...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
