I am evaluating QTR and so far am very happy but have some strange behaviour that I haven't been able to figure out. Basically if I print to file out of Qimage...
If you can hone in on the boundary condition, it will help in finding this problem. What is the length of the image? (You only mention 46 cm width.) How much...
Thanks Stephen, and thanks for your great work on the GUI. This particular image isn't that big - about 355 MB if memory serves as a 46 cm x 31 cm image at 720...
Isn't 46 cm simply too wide for a 2100? Ian ... Thanks Stephen, and thanks for your great work on the GUI. This particular image isn't that big - about 355 MB...
I suspect that there is a problem in handling the size file you are attempting to print. I will look into it and see what I can find. The TIFF code is not ...
... I'm not aware of any problems. Could it be your printer being misaligned? Unidirection printing (HiSpeed = Better) usually helps alignment issues. Roy...
This behavior happens with QTRgui 2.3.4. When I open a qidf file and select one of the Gray or Toner (1 or 2) tabs, QTRgui complains when I leave that tab...
Thanks Stephen. It does seem to be a problem. One thought I have is that I will try resizing the file in PS to 46 cm at 720 ppi and see if QTR accepts that....
Dave, One thing that wasn't clear before is that your image seems to be in landscape orientation i.e. 18in wide is really 18in length as printed. So the whole...
Roy, Stephen, Thanks. In the last hour I've discovered something. I tried the interpolation in PS and had the same result - the thumbnail would not show and I...
I can report the same problem. I uninstalled and reverted to the prior GUI. Dave ... and select ... leave that ... complain ... create a ... though....
Greetings: I am new to the QTR and have an Epson R-2400 printer running on a PC. I am using version 2.3.0 of the QTR. I have been following instructions that...
... misaligned? ... As it works fine with Qimage and Photoshop, and has problems only with QTR I doubt if its alignment (and especially so as at the time I...
I believe the width of the 2100/2200 is 13". Unless you turn the print so 18.1" is in the machine direction, it will be too wide. ... Thanks Stephen. It does...
Bill The section of the user guide you are referring to is related to creating new curves. I suspect you would only want to try printing at this point, using...
... Tom: I guess I will have to wait until someone adds Templates for the R- 2400. Thanks for your response. I have another question for you. Because the...
Hi, This message is to request help with a problem with the Quadtone RIP used for an Epson 2200 loaded with the Piezography K7 inkset. The Quadtone RIP...
Hi John, I have an Epson 2200 loaded with the Piezography K7 inset. I also have an Epson R2400 loaded with Epson's K3 inset. As a result, I've been able to...
Bill I can't speak for QTRs author (Roy Harrington) but I am quite sure that there will have to be an ink separation test page that prints each of the inks of...
Hi Tony, Thank you for the details of your test results. Is anyone using K7 in the 4000 or larger machines yet? What you experienced was exactly what I would...
I've used Cone's inks from nearly the beginning and they've always been first rate. The K7 shows two noticeable improvements that haven't been mentioned here...
... I print on Ilford SP and I get a lot more bronzing with QTR on a B&W than when I print using the Epson drivers with the same (Epson) inks on same paper, so...
Hi. I am not new to black and white inkjet printing. I have been at this since the first generation of piezography. I am new to this particular product...
Thanks Mark, Sounds good. So you have no complaints about the deepest black density with K7? I get the feeling this is going to be an excellent inkset for use...
... I don't have any complaints. I can't predict what a one would think if the deepest possible black is the first and foremost consideration however. The look...
I've been using the K7 inkset with my 4000 and both QTR and IJC/OPM and have had excellent results. Previously I was using QTR and IJC/OPM with the UC inks...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
