Is there any other solution than using cs3? I use cs5 and I was considering using qtr until I read this message....
9464
Walker Blackwell
wblackwellph
May 4, 2011 2:29 am
CS5 v12.01 / 10.6.6 / QTR 7 and Create-ICC works. I can confirm that. All the best, Walker ................................................... // Work Cell:...
9465
Harlan Chapman
hhchapman4104
May 4, 2011 3:04 pm
Hello Bob, Roy pointed out that CS5 converts to "generic gray gamma 2.2" on printing. I verified this by creating a step wedge in this profile and checking the...
9466
Walker Blackwell
wblackwellph
May 4, 2011 3:23 pm
Well, I don't know about other people but when I print with cs5/10.6.3 it converts to 2.2. When I print with cs5/10.6.6 it prints with the correct CreateICC...
9467
Lutsky, Berel
berel_lutsky
May 4, 2011 8:49 pm
Sometimes using one of the best BW printing solutions out there demands a bit of inconvenience - (and it is a small one ) workflow is Image worked in...
9468
Bob
mazawa1
May 4, 2011 11:19 pm
Thanks Harlan. I am sure I will have questions as I venture into the qtr world. Congrats to you too. Bob...
9469
mjvendrell2
May 8, 2011 10:14 pm
cannot figure out how to do this although it works on an olde XP machine. Any help appreciated. Thx! Michael Vendrell...
9470
Roy Harrington
royvharrington
May 9, 2011 4:44 pm
Hi Michael, On the Mac its just slightly more work. Look at Tutorial.pdf on the last couple of pages. It's headlined Bonjour printers but the same technique...
9471
Michel
mpa.lepretre
May 9, 2011 5:54 pm
Hello ! This is my first post : I am a french advertising photographer, and I like nice B&W, so I started to use QTR with many satisfactions : I get much...
9472
tboleyyh
May 9, 2011 8:28 pm
many of us have run into this. The easiest solution is to make sure you have at least about 1/2" leading and trailing margins, even if you have to add them...
9473
Michael Vendrell
mjvendrell2
May 10, 2011 1:44 pm
I've done what you suggest and when I try to run the scripts I still get the error message below that the R220 printer cannot be found. I have renamed the...
9474
Roy Harrington
royvharrington
May 10, 2011 3:59 pm
You can't rename the printer you need to create the printer with that name. -- turns out the system maintains the original name internally -- Roy ... -- Roy...
9475
Roy Harrington
royvharrington
May 10, 2011 4:00 pm
Also I notice you are using InstallR220-K6 so the printname must be QuadR220-K6 Roy ... -- Roy Harrington roy@... www.harrington.com...
9476
Michael Vendrell
mjvendrell2
May 10, 2011 4:13 pm
Thank you Roy. Finally worked for a Bonjour on my Time Capsule but I did get the alert below. What if anything needs to be done about the alert? Last login:...
9477
Roy Harrington
royvharrington
May 10, 2011 4:53 pm
Hi Michael, You probably aren't getting any curves installed if it can't create the folder. The issue is probably permission -- are you using both an admin and...
9478
Michael Vendrell
mjvendrell2
May 10, 2011 4:53 pm
I still cannot print from this printer using QTR and no profiles show up in printer QTR window. Any help appreciated. Thx. Michael J. Vendrell, MD ... ...
9479
mjvendrell2@...
mjvendrell2
May 10, 2011 6:26 pm
Success - finally. Had to do a complete un-install of QTR and printer. Reinstall QTR. Reinstall printer from locked screen so as to need PW as Quad220-K6. Then...
9480
Mel
chilterns...
May 10, 2011 6:55 pm
I cannot find any information on the forum with regard to this. I would like to know the suggested workflow using Photo and Eboni black and replacement of the...
9481
edward wiseman
pahtspix
May 10, 2011 7:25 pm
Mel.. From personal experience (3-4 1280's), the results with UT-2 inks was superb, EXCEPT that these inks will clog and finally kill-off your 12xx machine..I...
9482
edward wiseman
pahtspix
May 10, 2011 7:31 pm
Mel.. Just in case you MUST go with UT-2..Here's a link to what you were looking for: http://www.inksupply.com/ut2-1280.cfm Read it ALL The way DOWN.. Eddie ...
9483
james.long23
May 11, 2011 2:56 am
When setting up to print on my Epson 4800; in the paper feed section I only see the following options; Auto Sheet Feed Sheet Feed Roll Feed (cutter off) Roll...
9484
Andrew
andy8x10
May 11, 2011 11:04 am
I just started using QTR on the weekend and getting better with it. My digi-negs have never printed so good 'til now. One thing I have noticed is that prints...
9485
Mike Finley
efikim
May 11, 2011 11:19 am
I suspect most members on this list use QTR for their final prints, rather than printing negatives for alt (or silver) processes. Just in case you aren't aware...
9486
Michel
mpa.lepretre
May 11, 2011 11:55 am
Thanks for your answer ! As I use frequently A4 paper, to avoid reducing the printing area, I use the following method : On an A3 sheet of strong paper, I have...
9487
James Hoggard
jameshoggard...
May 11, 2011 1:03 pm
Select "Sheet Feed" ..That's it. Jamie ________________________________ From: james.long23 <james.long23@...> To: QuadtoneRIP@yahoogroups.com Sent: Tue,...
9488
Lutsky, Berel
berel_lutsky
May 11, 2011 1:11 pm
Set selection on the control panel to sheet feed - load your paper - when you print be sure to choose manual feed in the print dialogue Berel Lutsky ...
9489
Andrew
andy8x10
May 11, 2011 5:43 pm
What is this for? Thank you. N_OF_TONER_PARTS= TONER_HIGHLIGHT= TONER_SHADOW= TONER_GAMMA= TONER_CURVE= N_OF_TONER_2_PARTS= TONER_2_HIGHLIGHT= ...
9490
Mel
chilterns...
May 11, 2011 7:29 pm
Thanks Eddie for your replies - I find this a little worrying and will ask MIS for their comments re clogging. Mel...
9491
Mike Finley
efikim
May 11, 2011 7:37 pm
It depends on the inkset in use, but the toners are for adjusting the print tone towards warm/cold/sepia/selenium tones depending on what colour options are...
9492
Andrew
andy8x10
May 11, 2011 8:40 pm
Thanks Mike! I'll shut 'em off and see what happens then. andrew...
