hey all. can anyone suggest a cheap source of precut mats online? all i've been able to find are custom-cutting places, which defeats my purpose: cheap. and...
Look for Light Impressions, Bainbridge mats, and similar. Bainbridge pre-cut mats are very high quality ... not particularly cheap but worth it. Light...
... If you haven't looked at Dick Blick, that's where I'd start. Strangely, you might also find precut, standard sizes (5x7, 8x10, etc. windows in 8x10, 11x14...
... Most of the large art supply stores such as Moores, Michaels, Friedman, Sam Flax, Dick Blick, Utrecht, etc. sell precut mats and frames to match. Every ...
thanks everyone for the mat source suggestions! i've ordered some. as for cutting my own...i got a basica mat-cutter for christmas, and tried cutting some 8x10...
thanks for your suggestion, larry. i only have Michaels and Aaron Bros locally. Michaels doesn't have much of a selection at all. Aaron Bros does, but they...
Hi, The only online place I've bought from (well, a friend bought and I split an order with him) was this: http://matcutter.com/ They arrived with no dents,...
Just to pick up on this home mat cutting, I recently bought some mounting board from a local discount stationers (actually for making a neg mask for my flatbed...
46mm. i had Ligo make me a 127 slitter, and specified 45mm. it's slightly on the narrow side, but works fine. 46mm is the official width. ... -- matt haines ...
Hi all, A reminder: if you change ISPs, web hosts or otherwise change your email address, be sure to let me know so I can make the appropriate changes in the...
SUBMINI-L@yahoogroups...
Jan 4, 2007 4:45 pm
14837
I have an old Logan handheld cutter that I've used very successfully. It has the blade clamped in a pivot that swings down into the mat at the proper angle,...
When Aaron bros. has a frame sale they are very good. I bought a stack of nice black wood 16x20" frames for like $8 a peice. I upgraded the hardware and put ...
In a message dated 1/4/07 12:56:55 P.M. Mountain Standard Time, markhahn2000@... writes: When Aaron bros. has a frame sale they are very good. I bought...
... O_o K. Original 127 is 46 mm wide. That'll make three strips wide enough for most no-perf-needed 16 mm cameras, 4 and some waste for Minox, but only two...
As 127 film is all but unobtainable over here, I did consider that possibility, but decided that I must be mistaken! The film still has to fit the spool size...
... i was justgoing to say -- if you have so much 127 you can afford to slit it, you'd do better to sell it for $6 a roll and buy 35mm to slit for minox -- ...
So what is "drying out" from them, water? Could you add more through those little holes and how much? Mike Taglieri ... On Thu, 23 Nov 2006 11:28:20 -0800,...
... um, probably not. I'm no chemist, but the name "zinc-air" implies that oxygen in the air acts as a catalyst for whatever reaction is taking place in there,...
This site has most of the spool dimensions, including 127 (even though I got my hands smacked here on the 5th of November for asking about 127 film <VBG>) :- ...
mine is the Logan Freestyle Basic, model 1100. it's just the cutter, nothing else. no straight edge. $30? i can manage that. i'll take a look. thanks! ... -- ...
the day i read your email (last thursday...i've been a little slow in responding.), i went into Aaron Bros, and they were having their sale! and they no longer...
ok, I know someone is going to bitch... but has anyone tried an HP 4890 Scanjet with Minox b&w negatives? It is way cheap and does up to 4x5" with no...
This is an interesting coincidence Mark, as I too have been looking at these scanners, as they also go up to 4"x5", to replace my Epson 2480 which I can only...
I haven't used the HP scanners for anything, but have had good results from my Minolta Dual Scan Elite 5400 II. I made a mask to hold the negatives in the...
When you say that you made a mask Jack, was it just a couple of pieces of card to mask a single Minox frame please? Tony Wells. ... From: "Jack DeLisle"...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
