Hi, Ok it's all right: i update the cu, i charge the 3.41 program. I've done using the files wrote on the disk with diskcopy 8. Now I would like to charge the...
I would like to undertand the problem too. the problem is that i can't charge the ai and the negative color. Must I probabily use and internal fd reader? ...
My interpretation is: charge = install fd reader = floppy drive an internal floppy might be better but i'm really not sure. my install was using a G3 with...
... Hi Eric and Corrado! My name is Rainer, i'm very new in this group. My problem is obviously the same as Corrado's. I have a 1030AI (built 1994). The...
Still now, i used an old mac 4400 with a built in floppy disk, using the hd of my g4. after that i installed again the hd in my g4 and something seems work. So...
Hello All, It's my first post here, just to say "hello". I'll receive my screen dts1030ai next week. I hope to succeed to do a good scan by this week. All the...
hello , I've install DTS Scan but I'm stuck with the optional Nega Color Data 3.0_.image I own a G4 without a floppy drive, how could I mouth this image? When...
Hi, My new 1030 is ready. I have original install with old powermac 6100 and new install with G4 macos 9.2.2 In both case i have D3 error listed as Scanning is...
Hi Philippe, Do you follow the standard pre-scan process (i. e. Original point + White Calibration)? It's been years since I last used a DT-S, so I won't be...
Hi Philippe, My scanner is in storage at the moment, but from memory the reply below is correct. You need to do a white calibration on a clear part of the...
Hi, Thanks for your answer :) I need first to make scan origin (blue touch) and after to make calibration with blue touch + left touch (offline). After that...
Hi Philippe, I was told its best to mount a 4x5 with the short edge along the drum axis and the long edge around the drum. I think there may be a limitation on...
Hi All, I do 4x5" 5200dpi scan without any limits. I use a G4 with 1gb of ram on mac os 9.2 all the best, Arnaud ... Hi All, I do 4x5" 5200dpi scan without any...
Hi there, As far as I can remember, I used to set the White Cal. first then set the Origin Point. Make sure to have the White Cal. set on the cylinder itself,...
Hi, I'm on G4 with 9.2.2 and 2Go Ram. My test is not finish (it's long...) but seems to be ok. For the second test i try to make sharpness :) Thanks Philippe ...
Hi Arnaud, Thanks for this. I will have to get my 1030 up and running again. I ended up with a G3 Beige for scanning and a G4 Mirror Door for file conversion,...
Hi Philippe, Don't sharpen during the scan unless you have a specific reason to do so. Its far better to sharpen last thing, just before you save the final...
Hi, My first scan of 4x5 negative color was done :) It's long time... and as i don't make manual sharpness it is not good for that. But color seems to be very...
Hi, Thanks for all answer. My next problem is with nega color and ai channel plugin. I try a lot of thing on system 7,8 and 9 with norton, diskcopy 4,6,8 and...
Hi, Ok i find the way :) So for other newbee i give the way i find :) The good file to work with is in screen 1030 file disk image folder. There is a .sitx...
There you go! Exactly the workflow one should do as using OS 7-8-9 on the internet is just unpleasant. The files downloaded should be stored on your newer...
If you are working with an older Mac for scanning and using a newer Mac to work with those scans, getting them to the new Mac via your network can be an issue....
I hadn't used my 1030ai in a long time till yesterday and had a hard time remembering how I used to do things! It took me a while just to remember how to set...
Hello, Did you succeed to install the option, because I just tried all the combinations possible to install on my G4 mac 9.2.2 with a external floppy disk....
