Driver Emulator v1.02 Copyright (c) Patrick Whittle, 1995-7 DUMMY.ASM Source code for dummy packet driver (null device driver) TRACE.COM...
10135
Dan Creagan
dcreagan2000
Feb 1, 2002 12:19 pm
Be sure to buy more than one. You will break a few on the way to nirvana. Sears did have them in a kit of mini tools. Dan ... From: tad heckaman.com...
I have built a version of Keith Payea's cheap sonar system from the March '93 issue of the old paper version of The Encoder. I have a 'scope and sig-gen setup...
10138
bnansel@...
country_robot
Feb 1, 2002 11:08 pm
... I meant to say 114mm wide x 92mm high. It has a 10cm x 8cm graticule, nothing unsual. -RLN...
10139
Dan Creagan
dcreagan2000
Feb 2, 2002 1:35 pm
Robert, No help for the part numbers but I have had very good success with shooting a scope face with a digital camera by darkening the room and putting the ...
10140
bnansel@...
country_robot
Feb 2, 2002 2:33 pm
... I have gone this route in the past for scope shots, darkened room and all, but my digital camera has a hard-to-use macro focus, so it was always a hit and...
10141
bnansel@...
country_robot
Feb 2, 2002 3:40 pm
I remeasured my scope bezel, and the actual dimensions are 103mm x 119mm, not 92mm x 114mm as I stated earlier. That's what I get for trusting my memory....
10142
Dave Hylands
dhylands_99
Feb 2, 2002 5:17 pm
Hi, I have an Opal source file that I'd like to get converted into EQN format. This is the source for the GAL16V8 mentioned in the ICD2 cable found on ...
10143
Kenneth Maxon
kmaxon2002
Feb 2, 2002 7:24 pm
Ahh, source for GDB debugger's PAL. What compiler will you be using, I can probably help. -Kenneth (Unit 3's in trouble and it's scared out of its wits)...
10144
Kenneth Maxon
kmaxon2002
Feb 3, 2002 8:41 am
Group, I had further thoughts about Rich's article on Smarter Infrared Proximity Detectors and thought it might be worth a discussion thread which could refine...
10145
Larry Barello
lbarello
Feb 3, 2002 3:07 pm
You could implement synchronous detection. I.e. gate the illuminator and check the return signal. By checking both the "on" and "off" period you can...
10146
Kevin Ross
kevinwross
Feb 3, 2002 5:01 pm
... From: TVERCVER@... To: webmaster@... Sent: Saturday, February 02, 2002 8:25 PM Subject: K'NEX K-bot World Championships Dear Webmaster,...
10147
ankur mittal
ankurmittal32
Feb 3, 2002 5:47 pm
hi! nice to see that u r also third year engg. student u r from which country i am from delhi, india would u like to have friendship with me. i am keen to have...
10148
ankur mittal
ankurmittal32
Feb 3, 2002 5:49 pm
thanks Mr. Kevin I got the solution cheers ankur __________________________________________________ Do You Yahoo!? Great stuff seeking new owners in Yahoo!...
10149
Doug Kelley
douglasdrewk...
Feb 3, 2002 6:03 pm
I'll let our members know. Thanks! Doug...
10150
Doug Kelley
douglasdrewk...
Feb 3, 2002 6:07 pm
It seems IR is a little unreliable for sumos. Is anyone doing anything with sonar? It's slow, but might work well for minis. The little one that Acroname ...
10151
Thomas
thomas.looi@...
Feb 3, 2002 6:49 pm
Hello everyone, I was wondering if anyone could tell me where I could find a pushbutton switch on a handle. Sorta like the ones they have at hospitals on a bed...
10152
David Simmons
devs_ca
Feb 3, 2002 6:55 pm
Thomas, Make one!!! Take a pushbutton, add a tube, and a cord. Try a heavy pen body for the handle. Or even wood dowel with a hole drill down the centre. Be...
10153
Charles
thurston@...
Feb 3, 2002 7:01 pm
Howdy David, Ok call your local Alarm company and buy a " hardwired Medical Alert" pendant from them. Sunday, February 03, 2002, you wrote: DS> Thomas, DS>...
10154
Dafydd Walters
dafyddwalters
Feb 3, 2002 7:26 pm
... I'm using sonar on my mini-sumo (see http://www.davbot.com/lordnelson/ ) . It's the Devantech SRF04. This is used to confirm that the target is in front...
10155
Bob Dyer
bobdyer53
Feb 3, 2002 8:56 pm
Has anyone seen a linear displacement transducer that's not too expensive with at least 6 inches of travel? A slide pot would be ideal, (low friction, high...
10156
Kipton Moravec
kipton_moravec
Feb 3, 2002 9:05 pm
I saw some in the Allied catalog a month or so ago. They went up to 12 inches of travel. The Website is http://www.alliedelec.com In the past, I have had...
10157
Steve Greenfield
alienrelics
Feb 4, 2002 12:19 am
You may have to make one. Do you know how? Mind if I ask why you need such a long travel? Steve ... __________________________________________________ Do You...
10158
Donovan Parks
dparks3ca
Feb 4, 2002 12:35 am
Hello, Had to format my HD a couple weeks ago and am now wishing I had noted the links I had bookmarked. I went to look for a distributor of the Motorola ...
10159
John Edwards
grizbot
Feb 4, 2002 1:11 am
I think the site you are looking for is : http://www.findchips.com/ John Edwards ... From: "Donovan Parks" <dparks@...> To:...
10160
Dave Hylands
dhylands_99
Feb 4, 2002 1:13 am
Hi, I was wondering if anybody knows (and is willing to share) what the winning times for previous line maze competitions have been (and how big the line maze...
10161
Donovan Parks
dparks3ca
Feb 4, 2002 2:47 am
Hello, I'm in need of a stepper motor with a small step size (around 2 degree). I'm looking for a source for such a stepper motor - preferably Canadian. :-) ...
10162
Steve Greenfield
alienrelics
Feb 4, 2002 3:24 am
This may sound wierd- any Applewriter II printers around? The old dot matrix ones have wonderful 30oz-in 1.8 degree per step 6 wire stepper motors. I connected...
10163
Doug Kelley
douglasdrewk...
Feb 4, 2002 3:47 am
I think Larry has the record with 23 seconds on a 12' x 12' maze. As a side note, I just got my line maze entry running tonight! Geese, it took me long...
