Howdy!, The neat thing about piezoelectricity is that it works both ways - mechanical vibration is converted to an electrical signal and an electrical signal...
1539
carlk3jml@...
Sep 3, 2000 3:01 am
Check out http://divelec.tripod.com/gearmotor/gearmotor_flyer.htm for a gear head motor that might be what your looking for. ... From: Jeff Spencer To:...
1540
Jeff Spencer
jeffsp@...
Sep 3, 2000 3:46 am
While comparing gearhead motors I found a great free computer program for converting from any unit to measure to any other comparable unit of measure. It does...
1541
Bill Benson
wtbenson@...
Sep 3, 2000 5:49 am
The Home Brew Robotics Club (San Jose, CA) has moved its web site address to: http://www.geocities.com/homebrewrc...
1542
Randy Carter
rwcarter@...
Sep 3, 2000 3:15 pm
Are you sure that the plastic is plexiglass? They could be polycarconate. It makes nice windows but doesn't glue well. Tap plastics sells an adhesive that...
1543
Randy Carter
rwcarter@...
Sep 3, 2000 3:28 pm
I just took a straight slot jewelers screw driver and and wedged it into that three legged pattern. There isn't much torque required to remove them. When I...
1544
Dan Creagan
dcreagan@...
Sep 3, 2000 3:29 pm
I have used MEK and Acetone mixtures (see my previous message about mixing chips in the solvents) on both the polycarbonate window material and on Plex and it...
1545
clayton.wilson@...
Sep 3, 2000 3:48 pm
New amature (very) robot builder to the list. I would be very gratefull for help with the following questions. I want to a use the printer carraige of an Epson...
1546
Alexis Lussier Desbiens
alexis@...
Sep 3, 2000 4:36 pm
Hello, I have a sensor who take data at each 10 degres on a servo, the sensor take a value at 0 degre, then at 10, 20, 30,...180 and restart to 0... I would...
1547
BusterBot@...
Sep 3, 2000 4:55 pm
Im going to try the the "chip solvent method" if that doesnt work very well then I'll pick up some stuff from Tap. Thanks again. And yes I know work ...
1548
Randy Carter
rwcarter@...
Sep 3, 2000 6:00 pm
Ivar, I still have your coat that you left at the SRS meeting back in February. We need to make arrangements to get it back to you....
1549
M.Jones Hubert
mjhubert@...
Sep 3, 2000 7:47 pm
Does anyone have an idea of using GBCam boards?.. ...or these beautiful boards'll be garbage??!!.. Cheers, Matt ...
1550
brian rippie
b_rippie@...
Sep 3, 2000 8:08 pm
I have an old speak and read made by texas instruments. It was made back in 1980 for kids to help with spelling and pronunciation . I have kept this for years...
1551
Aaron and Hifumi
aaron_hifumi@...
Sep 3, 2000 11:19 pm
While building a sensor that swept a GP2D02 back and forth using a servo, I noticed something similar. I needed fairly accurate repeatability also, and I...
1552
RoboVac
robovac@...
Sep 4, 2000 12:08 am
Typically servo style motors work best if you need to control position, speed, and torque. If you just need to control position try using stepper motors....
1553
erba_13@...
Sep 4, 2000 12:50 am
i was just woundering if battle bots was on tv in canada (mainly in b.c.) if so when and what channel thanx...
1554
Dafydd Walters
dafydd@...
Sep 4, 2000 6:45 am
I've also had similar problems using PCBUG11, and have now tried Kevin's DL11 without success. My target board is an HC11A1 board with 32KB of SRAM based at...
1555
Jeff Spencer
jeffsp@...
Sep 4, 2000 6:57 am
The error message you're getting means that it tried to write to an address and once it thought it should be fully programmed it read a different value. I'm...
1556
Kevin Ross
kevinro@...
Sep 4, 2000 7:11 am
... From: Dafydd Walters <dafydd@...> To: <SeattleRobotics@egroups.com> Sent: Sunday, September 03, 2000 11:44 PM Subject: [SeattleRobotics] Re: please...
1557
Dafydd Walters
dafydd@...
Sep 4, 2000 8:00 am
Kevin, Thanks for v. quick & informative response. ... Still seeing the same error message. FYI I went down the 'checklist' that is dumped out by DL11 when the...
1558
SeattleRobotics@egrou...
Sep 4, 2000 2:02 pm
We would like to remind you of this upcoming event. Monday Night Chat Date: Monday, September 4, 2000 Time: 7:00PM - 9:00PM PDT (GMT-07:00) Monday Night Chat...
1559
Larry Barello
lbarello@...
Sep 4, 2000 2:56 pm
I am unable to get the mIrc program to connect on my system (win98, external DSL modem running NAT) I have the latest version: 5.71t First of all: the...
1560
Kevin Ross
kevinro@...
Sep 4, 2000 3:48 pm
... From: Larry Barello <lbarello@...> To: <SeattleRobotics@egroups.com> Sent: Monday, September 04, 2000 7:58 AM Subject: Re: [SeattleRobotics]...
1561
Kevin Ross
kevinro@...
Sep 4, 2000 3:58 pm
For better instructions connection instructions, check out http://www.seattlerobotics.org/contact.html#Monday Thanks Kevin...
1562
Jeff Spencer
jeffsp@...
Sep 4, 2000 5:13 pm
I'm running Windows Millenium with DSL through a Windows 98 Second Editition NAT (Internet Connection Sharing) with no problems. The DSL comes into the Windows...
1563
slickw@...
Sep 4, 2000 6:45 pm
Looking for information on how to convert standard Tv video output from say a VCR or the like to a regular computer monitor. I have a bunch of old but good PC...
1564
Larry Barello
lbarello@...
Sep 4, 2000 11:49 pm
I want to get two packs of the following batteries for my digital camera: http://www.4cbradio.com/maha-mh-aa155.htm And, possibly, one of their "super...
1565
SeattleRobotics@egrou...
Sep 5, 2000 1:02 am
We would like to remind you of this upcoming event. Monday Night Chat Date: Monday, September 4, 2000 Time: 7:00PM - 9:00PM PDT (GMT-07:00) Monday Night Chat...
1566
Dafydd Walters
dafydd@...
Sep 5, 2000 1:34 am
Hi, Those who've seen my most recent posts know that I was having problems downloading code to my HC11-based robot. I'm happy to report that I am now up and...
