I have setup gateway/gateway IPsec VPN between two sites. Tunnel show "running" at my end but I can not ping or connect to the local network at the remote...
... Depending on the quality of your internet feeds at both sites, you may simply have to reduce the IPSec MTU value. In order for me to achieve a stable IPSec...
... To save you from any more head banging, this is a known "feature" in the SnapGear firmware. It exists in firmware 3.1.6, and as far as I know remains...
Hello all, I am the "IT" guy, by default at our small business. We have an SG560 that we've been using for about 2 years now. We didn't change anything on it,...
... what do you mean with "when they're in"? Normally you attach a switch to the lan port. Attach an Acces point to it. Insert an IP adress (switch off the...
"When they're in" means when I have an engineer or sales person on the premises, who needs access to the internet. It's the second possibility that I'm looking...
Oh sorry, PF means packet filtering. the easiest way in my second scenario is -> to put the second port into lan or dmz mode... create a packet filtering rule...
Hi >Developers, i get ... # mkfs.ext2 /dev/sda1 mke2fs 1.39 (29-May-2006) /dev/sda1: Memory allocation failed while setting up superblock ... is there any...
Nothing comes to mind other than to mkfs on a bigger machine running linux. That is, work around the problem by using a different piece of hardware that has...
We're getting ready to put in an asterisk-based phone system in our two offices and we want to try to ensure that the VoIP traffic between them has top...
Hi, we realized this earlier succesfully with two sg530s. (btw a layer 3 switch is a better choice for this project) if you are hundred percent sure what you...
Each location has its own domain controller (same domain) which handles DHCP for that office. When it comes to this level of networking I'm a little bit...
Hi tom, Ok it is working... i played a lot with mkfs settings. in my case i was being able to create three partitions with +300G. mkfs.ext2 -j /dev/sda1 ...
Sorry, this is off the scope of your question, but I also have trixbox setup for a client and also sg300 (s) connecting 2 sites via VPN. I tried to connect...
So far we just have 1 trixbox server and it's at the remote site. The server at the main office is going to be installed in a couple of weeks. That being...
Brad, thanks for the reply. Yes, I am able to ping other computers on the network.( at least I'm able to ping the domain server 192.168.5.10). My trixbox is...
I don't really know much about trixbox or asterisk itself since we've actually got a 3rd party handling all of that for us, but it sounds like there might be...
Thats what I was thinking too. can you help me ask the guys that setup your maybe. are u guys using trixbox 2.6.1 too? or a different version. Nobody good in...
if you cannot ping this box ...but being able to see other IP Addresses, then you have to check your Gateway settings in this asterix linux box. ... From:...
Hmmm, Come to think of it, I actually did remove the gateway from the LAN Config settings. I did this to ensure better security and to prevent the box from...
In the past I have worked with a handful of other PPTP-enabled firewalls and in each case I found that when a client successfully connected to the device in...
I mentioned this also in the past. my workaround was to create an alias network on the LAN side and hand out alias 'server and network' to the pptp clients. ...
FOlks, just tried to upgrade the firmware but the 3.1.6 just factory-resets and does not keep the settings. Same happens when I try to manually load the 3.1.2...
I believe whether you are able to access the internet or not with a PPTP Established is imitially based on the client side. With Windows PPTP Client, by...
yeaph ...this makes sense. in my case certain family members are using my pptp server as a content scanner. (when surfing the internet they may use it as a...
Hi All, i would like to attach a fast 2.5 SSD at the usb ports of my SG565. All external 2.5 HDs (i tried) are not working, because of the low voltage of the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
