I just finished the assembly of Sumo11 expansion board and mount on the main board without LCD. The Main Board Red LED went on and off. As soon as I mount the...
The expansion board is designed to use Interactive C. I program in assembler. How would the Sumo11 have to be configured to use the expansion memory without...
This page will give you most of what you need to run the Expanded Sumo11 with assembly language. http://www.1sorc.com/guide/s11_memmap.html There's a lot of...
I just got this "Complete Sumo11 Sets" last week from web site http://www.1sorc.com/main/complete.html and how can I find the version of the main board? ... ...
Paul, The board will be marked Sumo11 brd Rev x.x but if you just got your kit recently then I'm sure it is a Rev.2.1 board. I just needed to be sure you...
i'm intrested in these sumo11 boards this would be my first robotics project so i have a few questions: - do you sell these boards assembled, cause i don't...
Reinout, Your situation is a tuff one, shipping between USA and Germany is terrible. It usually takes anywhere from 6 to 8 weeks, is fairly expensive and has...
Reinout, Here's a little help with your questions - I'm sure Dan Gates will post info for you also... The website has assembled boards listed for sale, both...
ok, i have started to love sumo11 already without me owning one... i'll do my best to get one, but before that i have 1 question: lets say i also buy this...
Yes, you could send images to your laptop using bluetooth, I'm not sure about doing it wifi. The CMUcam has a Frame Dump command that allows you to view what...
Dan, I am not sure about being able to do both the SUMO11 interface and the wireless at the same time. I think I would just look for a cheap USB Web cam with a...
I believe there are wireless transievers that can be connected to the SPI port and used to send information to a PC even while the CMUcam is in use on the...
Dan, From my experience with CMUcam I would never recommend that anyone try to use it as a source for transmitting video. It has poor quality and low...
RoboJDE version 1.3 is a Java development and execution environment for the Handy Board, Sumo11, and IntelliBrain robotics controllers. RoboJDE version 1.3...
I downloaded and installed IC4.3.01. I then ran Sumo11patch_4.3. IC4.301 told me that I had the wrong libaries. Powered off the Sumo11 and then powered it on...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the Sumo11users group. File : /IC -...
Sumo11users@yahoogrou...
Sep 16, 2004 12:25 am
270
I thought I got it from your website. Not sure. However, things are going from bad to worse. I am crashing in main(), i.e. program stops responding/running...
I'm not sure what would be causing that, I need more info. Has that particular program worked on the Sumo11 before? Is the battery fresh? Are you choosing the...
I have tried two new batteries and am sure that I have picked the picture of the Sumo11. Program has been uploaded. The program in memory does not have the...
John, I'm still not sure what the trouble is, did this program work fine in IC4.21? Is it only crashing in IC 4.3? Do you still get the wrong version error in...
This is in IC4.21, I went back to that. I replaced the Sharp IR sensors with the wide angle version. I loaded a test program that just writes out the analog...
Try loading my very basic Sumo code and see what happens, that will at least tell us if it's the board or the code. My code is in the files section called...
I cannot get that far. When I start IC it tries to connect to the Sumo11. It fails and gives a message saying to check connections or download firmware. If...
John, I think it's probably something simple, old Sumo11 boards had there start and stop buttons reversed. I did a temporary fix in the software, but the new...
Do you know that the Sumo11 with the expansion board has 4 servo output pulse generators built-in? Using IC all the output libraries are attached also. All...
Has anybody controlled the D200(www.tecel.com/d200) motor driver board from Tecel with the Summo11? I would like to know how reliable is it at 40A. ak......
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
