RoboJDE version 1.3 is a Java development and execution environment for the Handy Board, Sumo11, and IntelliBrain robotics controllers. RoboJDE version 1.3...
I downloaded and installed IC4.3.01. I then ran Sumo11patch_4.3. IC4.301 told me that I had the wrong libaries. Powered off the Sumo11 and then powered it on...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the Sumo11users group. File : /IC -...
Sumo11users@yahoogrou...
Sep 16, 2004 12:25 am
270
I thought I got it from your website. Not sure. However, things are going from bad to worse. I am crashing in main(), i.e. program stops responding/running...
I'm not sure what would be causing that, I need more info. Has that particular program worked on the Sumo11 before? Is the battery fresh? Are you choosing the...
I have tried two new batteries and am sure that I have picked the picture of the Sumo11. Program has been uploaded. The program in memory does not have the...
John, I'm still not sure what the trouble is, did this program work fine in IC4.21? Is it only crashing in IC 4.3? Do you still get the wrong version error in...
This is in IC4.21, I went back to that. I replaced the Sharp IR sensors with the wide angle version. I loaded a test program that just writes out the analog...
Try loading my very basic Sumo code and see what happens, that will at least tell us if it's the board or the code. My code is in the files section called...
I cannot get that far. When I start IC it tries to connect to the Sumo11. It fails and gives a message saying to check connections or download firmware. If...
John, I think it's probably something simple, old Sumo11 boards had there start and stop buttons reversed. I did a temporary fix in the software, but the new...
Do you know that the Sumo11 with the expansion board has 4 servo output pulse generators built-in? Using IC all the output libraries are attached also. All...
Has anybody controlled the D200(www.tecel.com/d200) motor driver board from Tecel with the Summo11? I would like to know how reliable is it at 40A. ak......
All, I posted this question over on the Mark III forum as well: for what applications was the Sumo11 board developed? For the applications of line following...
Richard, When I designed the Sumo11 I had three main goals, Mainly I wanted the power of the popular Handyboard in a size that could fit on a Mini-Sumo. If...
Dan, All good reasons. I am not familiary with the Handyboard - as you say, it has always been pricey. I have been thinking about building a 3d Mark III and...
I ordered the Sumo11 kit and now I need to find an application! I recently purchased the CMUcam and I was thinking about BOT ball. I looked around over at...
If you have IC 4.3 there should be a CMUCAMlib.ic set of files that provides init and track functions. Be sure you get the CMUcam manual for the camera...
Perfect! I do have IC and the files are there. I may have to make some changes for the newer camera but that shouldn't be too difficult. I also have to work...
My SUMO11 is in the mail, presumably, and I am already daydreaming about version 3 of my botware. Has anyone ever hooked an ethernet card onto a SUMO11 (and...
I am not sure what your skill level is for board development, but google "HC11 ETHERNET" for some HC11 IP projects. UDP appears to be the preferred protocol....
Or look at the offerings at Rabbit Semiconductor and build an expansion board using their chip and stack for communications. ... google ... daydreaming about ...
First, the Sumo11 went together quickly. Single board mode works as does IC 4.30 from the GUI. The analog, knob and servo tests all work when the program is...
The SUMO11 will run the currently loaded program starting with the void main() function each time it is powered up if one is loaded. The base libraries do not...
Dan, I noticed on my new Sumo11 that the servos are premodified. In fact, the controller has a pot accessible from the rear end (as mounted). I am curious...
Richard, These servos are a new thing for me, the adjustment may not be in the best place for a Sumo robot. I liked the idea of being able to supply...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
