... Do you know if I can use an IBM 8-bit floppy disk controller on the Tandy 1000 TX and use a IBM type 1.44MB floppy drive? The answer is YES. The extra FDD...
... I'm sure Mr Hayes is a very knowledgeable guy, but following his instructions to the letter in modifying the data cable to allow for the use of a generic...
... you ... the ... If you connect any 3.5 FDD to the built-in controller it will never be a high density drive! To read, write and format 1.44MB (not 1.33 as...
Hello, it makes me very sad that due to someone selling and making a profit off of dvds containing a copy of Ira Goldklang's archive that she has as a result...
... O.K. Mike, first of all I know enough to know that I wouldn't have been able to make the generic floppy work as a high density drive. All I was shooting...
It is my belief that archives like this one should be provided without any limitation to the end users ability to utilize the archive. These archives are...
All right, all of you Tandy 1000 experts...here's one for you: I'm trying to add a vintage hard disk to my vintage 1000A. I know there are lot's of choices,...
Hallo, ... From: Tandy1000@yahoogroups.com [mailto:Tandy1000@yahoogroups.com] On Behalf Of louisstdubois ... The default format that the FORMAT-commado uses on...
Due to the large amount of people who didn't want to use KDX to connect to my server and instead expressed interest in FTP access I have decided to set up FTP...
The complaints keep on growing about my choice of KDX as the server of the files I have. Do not worry, I most definitely listen to the comments I receive about...
Thank you very much, sir. I will try that and get back with you on my possible success. I've replaced the old generic floppy drive with a new Sony (better...
... Hello, I don't have thousands of passive ports open because of the limited bandwidth I have, instead I have just enough passive ports open such that if...
My mouseclock calendar drivers floppy got messed up somehow and I can't seem to find them on TVDog's website. Can anyone here help me out? Thanks for any...
Hey people! I had to buy another TX to prove it to myself, but the three and a half inch drives in the 1000 TX and others like the external three and half...
Hey out there all you Tandy freaks! I just messed up the setup or BIOS on my TL2. I somehow messed things up so bad that I can't get it to read from the...
On Sat, 21 Jul 2007 18:00:59 -0700 (PDT), Edgar Webb <louisstdubois@...> had a flock of green cheek conures squawk ... I have two of the external 3.5"...
Hi, Try 'FORMAT X: /T:80 /N:9' (where X: is A: or B:) Should work with any DOS 3.2 or up. The external 3.5" HX drive definitely works, formatting 720 KB,...
I've been trying every config.sys I was offered on this TX and had no luck, even with PCDOS 5.0 I got "parameters not supported". I'll have to try yours on...
On Sun, 22 Jul 2007 14:40:24 -0700 (PDT), Edgar Webb <louisstdubois@...> had a flock of green cheek conures squawk ... It should work from DOS 3.2 to...
Hi folks. I found the drivers in some old floppies I had stored away. If anyone needs them I'll be glad to send them as an attachment if that's ok. Louis ...
You could upload them here if you have the capability. Neil ... away. If anyone needs them I'll be glad to send them as an attachment if that's ok. Louis...
What deskmate disks should I use with my new 1000 SL? I know about the built in deskmate, but that doesn't include everything. I didn't see a specific version...
Did you try the versions from the files section here? Note that special versions of DM add extra features for specific hardware bu tthe generic version should...
I can't tell you much about which Deskmate version you should be looking for. I use Deskmate II on my 1000 TX which is appropriate, even though nobody seems...
I was looking for a version that would tie in with the rom installed version. I know it is version 3.something. I'll try to figure out exactly what it is and...