All right, all of you Tandy 1000 experts...here's one for you: I'm trying to add a vintage hard disk to my vintage 1000A. I know there are lot's of choices,...
Hallo, ... From: Tandy1000@yahoogroups.com [mailto:Tandy1000@yahoogroups.com] On Behalf Of louisstdubois ... The default format that the FORMAT-commado uses on...
Due to the large amount of people who didn't want to use KDX to connect to my server and instead expressed interest in FTP access I have decided to set up FTP...
The complaints keep on growing about my choice of KDX as the server of the files I have. Do not worry, I most definitely listen to the comments I receive about...
Thank you very much, sir. I will try that and get back with you on my possible success. I've replaced the old generic floppy drive with a new Sony (better...
... Hello, I don't have thousands of passive ports open because of the limited bandwidth I have, instead I have just enough passive ports open such that if...
My mouseclock calendar drivers floppy got messed up somehow and I can't seem to find them on TVDog's website. Can anyone here help me out? Thanks for any...
Hey people! I had to buy another TX to prove it to myself, but the three and a half inch drives in the 1000 TX and others like the external three and half...
Hey out there all you Tandy freaks! I just messed up the setup or BIOS on my TL2. I somehow messed things up so bad that I can't get it to read from the...
On Sat, 21 Jul 2007 18:00:59 -0700 (PDT), Edgar Webb <louisstdubois@...> had a flock of green cheek conures squawk ... I have two of the external 3.5"...
Hi, Try 'FORMAT X: /T:80 /N:9' (where X: is A: or B:) Should work with any DOS 3.2 or up. The external 3.5" HX drive definitely works, formatting 720 KB,...
I've been trying every config.sys I was offered on this TX and had no luck, even with PCDOS 5.0 I got "parameters not supported". I'll have to try yours on...
On Sun, 22 Jul 2007 14:40:24 -0700 (PDT), Edgar Webb <louisstdubois@...> had a flock of green cheek conures squawk ... It should work from DOS 3.2 to...
Hi folks. I found the drivers in some old floppies I had stored away. If anyone needs them I'll be glad to send them as an attachment if that's ok. Louis ...
You could upload them here if you have the capability. Neil ... away. If anyone needs them I'll be glad to send them as an attachment if that's ok. Louis...
What deskmate disks should I use with my new 1000 SL? I know about the built in deskmate, but that doesn't include everything. I didn't see a specific version...
Did you try the versions from the files section here? Note that special versions of DM add extra features for specific hardware bu tthe generic version should...
I can't tell you much about which Deskmate version you should be looking for. I use Deskmate II on my 1000 TX which is appropriate, even though nobody seems...
I was looking for a version that would tie in with the rom installed version. I know it is version 3.something. I'll try to figure out exactly what it is and...
Hallo, AFAIK, every generation of the Tandy 1000 had a different version of DM. And of course, they were not interchangeable... DM in ROM made it even more ...
Hi again folks. Also, if you get a WD hdd without the park software, don't forget to use shiptrak in DOS. I know it's supposed to be for moving your PC, but...
... There were a few drives that would do both AT & XT. More likely to be findable are the cards that allow using AT drives in XTs. Even those are gonna be...
Version 3.00 from tvdog's site is the one for the SL. At least it worked properly, and the startup flag from ROM reads deskmate 3.00. download it from...
I have verified that Version 3.00 from the tvdog site works with the built in version. Starting desk from ROM showed a version 3.00 banner prior to starting. ...
After a few months, I'm going to try again at this. Remember, I have not the slightest idea about how any electric - electronic circuit works, but I did try...