Please ban this person from posting I have seen enough of these commercials. If I was looking for a mortgage I would go to the homeloan@yahoo group. This ...
It has been very quiet on here. Has anybody got information on Tesla turbines using water rather than hot combustion gasses or steam. There seems to have been...
While water could possibly be used, the applications for it are limited by the available water source. Using the TT as a water turbine is probably not ...
... From: Jim Dooley [mailto:LSUman@...] Sent: Monday, July 11, 2005 9:20 AM To: TeslaTurbine@yahoogroups.com Subject: RE: [TeslaTurbine] Water turbine ...
The application is power generation, the idea is patentable so I do not wish to divulge any more for the moment. I am trying to determine the mass flow and...
Hello group; I am looking for information on using the TT as an air pump. Specifically; Is there a temperature differential between in/out. If so how much?....
Luis, Yes, there is a temperature differential. As in any compressor, the compressed air will have a higher temperature than the entering air. This is...
... From: Jim Dooley [mailto:LSUman@...] Sent: Tuesday, July 12, 2005 8:03 AM To: TeslaTurbine@yahoogroups.com Subject: RE: [TeslaTurbine] Looking for...
At 10:31 12-07-05 -0700, McGalliard, Frederick B wrote: From: Jim Dooley [mailto:LSUman@...] ... Jim, Fred, that's all very interesting but it addresses...
... A tesla turbine produces a mass flow rate (lbs of air per second) that is proportional to the number of disks, and to some more complex factor for the RPM....
... ...which requires a torque of ____ foot-pounds, resulting in an input shaft horsepower requirement of ____. ... Can that possibly be right? Gadzooks! The...
... RPMs. ... the bar! :( Actually, the disk doesn't need much strength since it is just rotating under a strong breeze, more or less. In fact, for this kind...
... Yep. It's easy to come up with a design that would be impossible to manufacture. I'm reading up on Hirsch Vortex design, and trying to correlate with ...
... Are there any decent graphical representations of this? Or must the reader/builder take a best guess on what this would look like? Don't say "look at the...
I studied general physics, not aerodynamics and gas flow, so I don't have any personal references to this stuff. Some of the tesla turbine folk have come...
Reese, I am a member of the Tesla Engine Builders Association (TEBA). I have not heard or seen anything from the association in quite some time, though. There...
Hello everyone. I have recently become interested in the Tesla turbine while looking for a possible power source that could be used in the wild that would be...
... I was also considering hard drive data platters for a turbine, though I sought out some older 5.25" drives and was going to use those. I hoped to drive the...
3 GREAT WEEKEND SHOWS ... SATURDAY - Fun Show! Laugh a lot !!! *BLKNIGHT AND SQUIRE G LIVE in da Studios... Saturday: 3PM-6PM Eastern, 2PM-5PM Central, 1PM-4PM...
To all I uploaded a avi movie of my tiny turbine running. It's in the files section of our member page. I'm still looking for more data on the turbine as a...
Good Work Andy!! mtndrew77 <twosimple4u77@...> wrote:To all I uploaded a avi movie of my tiny turbine running. It's in the files section of our member...
... I suggest you envision a spiral wrapped around the axel 5-10 times, narrowing in crossection as it spirals out. The outer casing needs to wrap around at...
I'm not following your explanation. If you could draw me a picture that would be the most helpful. Thank's for writting Cheer's Andy ... I suggest you envision...
Are you a engineer at boeing? Do you have access to CAD program? I use Pro E. I plan on modeling everything before I build it. If you could take a look when...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
