How do I rotate a square in 2d that has been rotated an unknown number of degrees, to be back on the square? I was looking for the option to have the selection...
MH, 1) Turn on "Extended Ortho" Snap. 2) Select the square 3) Press 'D' on the keyboard and snap the origin to a corner of the square 4) Press [Control] and...
I am evaluating version 10pro to see if I want to upgrade. I can not get the chamfer to work on solids. It gives me the message Radius must be positive number....
Negative radii would be interesting - Grove ... From: Terry Mills To: TurboCAD-File-Library@yahoogroups.com Sent: Sunday, October 03, 2004 9:26 AM Subject:...
Tell me I even tried to enter a negative just to see if it was evaluating my input wrong. Then I started a new solid body and then chamfer worked. Then I went...
1638
RoTierney
rotierney@...
Oct 3, 2004 10:39 pm
Another tool to try- "assemble by three points". For 2d, use only 2 of the 3 points available. You can use this for re-aligning 2d objects. The first point...
Maybe you've done this already, but try pointing your browser to this page... <http://www.imsisoft.com/support/turbocad/turbocad_documentation.asp> On that...
Both the Snip and the original URLs produce a page where this can be selected: ============== TurboCAD v8 TurboCAD v8 Courseware There is no better way to...
Hello All I am using TC 7.1 . A few months ago, the small box to help user to enter radius, diameter or circumference when drafting a circle disappear after a ...
OK, I see the problem. I'll email George about it. Meanwhile, you can download the v6 manual and the v7 a/v stuff, which is 99% (probably 100%) applicable to...
Jacques, A couple things to check: first, go to the Workspace menu and see if Inspector Bar is checked. If not, check it. Now start the circle tool and...
Many thanks, Joe, now everything perfect after a global reset Jacques ... From: "Joe Tilman" <mrtilman@...> To: <TurboCAD-File-Library@yahoogroups.com> ...
Mike, Thanks for the tip. That site is now bookmarked! The v.8 material was either not available (IMSI site) or unable to open. However, I did download user...
No, the program sends you to the website for the tuts. Kathy Dickinson <haleasdollclothes@...> wrote: Hi, Mario. Aren't there some right in the program? ...
Don Cheke has created some excellent tutorials for V9 and V10 Pro (http://www.textualcreations.ca/). I think he may have some for the deluxe version too. Kelly...
Hello all: Need some help here with v-6. Been using this version for several years off and on. After copying some files and them restoring them to a new hard...
Bob, Did you ever experiment with a free trial of a later version? The error you are describing usually means you are trying to open a later version file than...
Thanks guys for your help. Mario lloyd sumner <las32780@...> wrote: instead goto this one. http://www.softdevspb.com/Techsupport/Documentation/ ... ...
Hi, I had copied my TCW files to a CD disk. Now, I can not open the files with my AutoCAD Pro V6. I got the message: "Failed to open <path>\<file>.tcw: Stream...
Hello, Everyone. I have purchased the Deluxe v10 and would like to know if Deluxe v9.1 and 9.2 have .dxf files on them. I am creating doll clothes patterns...
1661
RoTierney
rotierney@...
Oct 14, 2004 2:42 am
I don't have Deluxe v9.1/9.2 but I think it is the same as what was called TurbCAD Standard. TurboCAD standard can save as DXF. Version 7.1 Standard for...
