I tried using this technique with a 24 inch x 30 inch BW print and it seemed to work well except for one thing. While peeling back the backing paper and...
Use Cotton gloves? And make sure print is thoroughly dry. Maybe use a hair dryer before mounting? Prints I was mounting were on Photo RC paper, semi-matte...
It sounds as if either the printer profile is putting too much ink down for the media or else the media isn't good for the kind of ink you're using and it...
My 24" Z3100 has just started spitting large amounts of ink at the edge of prints. It doesn't do it all the time but about one print in 20 or so. I first...
... Set the printer in head exchange mode. Pull the power cable out, switch the printer off. Get a torch and check the capping station at the right side ...
Ernst, Thank you for that extremely comprehensive reply. Do you find you have to routinely clean your printer to avoid this? Regards Matthew ... Matthew...
I guess too much ink on the print is possible (I'm new to inkjet printing) but I don't think so. The print was a foggy landscape which was composed almost...
Matthew, My Z3100 44" does the same thing from time to time. I've found there is a great amount of over spray from the print head carriage which will "leak"...
Richard, Thank you for your reply. I don't know if you have seen Ernst's earlier reply to me but I followed that to the letter and apart from being incredibly...
Matthew, I did see Ernst's reply after I sent mine. He has great experience with the equipment and his advice is always good. Regards, Richard In a message...
Does anyone use Mac OX 10.5 to print to the Epson 7600 printer? I understand from the Epson site that it has limited driver support but it doesn't describe...
... I am... printing to a 9600 just fine. 10.5.5 on an Intel Powerbook. The driver shows as version 3.09 Bob Smith Accurate Image • Bob Smith Photographer...
Thanks for the info. Did you have any surprises with color handling with the driver going from Tiger to Leopard? Mark http://www.stillrivereditions.com ... ...
... An Intel Powerbook - is there such a thing? All Powerbooks, Powermacs were PowerPC, not Intel, hence the name. The Intel equivalent of a Powerbook is the...
... MacBook... sorry. I still have and use both a Powerbook and a Macbook. The Macbook running 10.5.5 prints just fine to the 9600. That's probably the...
I've been trying to use Canon's Polished Rag paper with my Canon imagePrograf 5100 printer. The results are awful! Colors are wrong (especially blues/greens,...
Sounds like you are using the wrong profile for the paper and maybe the wrong paper setting. The silvery sheen could be caused by too much ink laydown...
Hi The Canon Premium RC Photo Luster is probably the closest to the Epson luster http://usa.canon.com/consumables/pdf/Pivot-Table.xls You can get free premium...
Thanks everyone for your input - I'm not as afraid to invest in a new mac knowing that others are having good success Is anyone using the new Imac? How good...
I got on for a workstation, it is very uneven from left to right in brightness. My went in for repair two times and it still has same issue. If you google the...
I hope I’m not out of line posting this here, but I have a 44” Z3100 for sale along with some extra inks. If anyone is interested, please contact me off...
My Z3100 is leaving black ink "smears" and small, short horizontal lines (<1-inch) whenever I start printing but only after a paper cut or when loading a fresh...
You have to go through the panel as if you are replacing heads. Pull one head at the time and clean gunk at the bottom of the heads. That should do it. Fima...
Thanks Fima. I'll give it a try. Does this procedure, pulling the heads and cleaning them, reset a counter or timer that schedules head replacement? Rick...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
