... Happy New Year to all members!! Been off for a while. New gasifier project is materialising in the workshop. I'll update after the maiden firing up. Hello...
Happy -2010- Everybody "Insulation is sexy stuff." Barack Obama "What we need is an energy policy based on consumption." George W. Bush "If we start...
May everyone have a happy and prosperous new year! May the resurgence of gasification as a viable energy alternative continue and grow stronger! May the new...
Hi John Bigotes, So you have 3 remaining after 7 so 10 ? Most folks have 7 or 8 hence the digits in our phone numbers. I thought you were headed to Peru ?? I...
HAPPY NEW YEAR to all; Especially Greg M., Bruce, Mike L. and the folks in Europe; I have ONE question for 2010--- 400,000 cars were driven on woodgas during...
Hey MikeL. The technicians trick to that coil replacement on the sidewinder GM V6's is to remove the upper front motor mount strut and pull the engine forward...
Whew! between Tom C. and bigotes we can all start researching and studying full time. Excelent outlook and If I don't allow discouragement these valid points...
Happy new year Mike e all Gasifiers. Mike below follows link of the video of mine pickup moved by gasogenio what you found, Mike and all ? Best Regards...
Hi Tom, I believe Johan made a reducer for the restriction / reduction cone on the imbert he was running. I could be all wet on this and it might have been...
Mike, Good luck with that monkey and that football. Why do car problems always pick some really nasty cold weather? Just keep in mind that the automotive...
Danilo, Good to hear from you and good to see you are still using that old charcoal cross draft on a truck now. It's a whole different design than what most of...
Tom, This is a crazy thought, but...if your Blazer is til all hooked up. Take out all the fuel blocks. Clean it all out. Then bake all the fuel on some type of...
--Hello Mike L Yes I enjoy taking with your phone machine when i have extra minutes on my phone . Richard Ramsey and his Dad came by and I gave them a ride in...
Bruce & Tom, Wayne used to partially pre-char all of his wood back when he was running a fema type unit. He was using full sized slab cut into 3 or 4 inch...
Thanks Mike, I think that cross-fire more needs to be studied/used, my model is a gohin-poulenc and it use only a steel scrap filter, its gas is extremely...
Tom C, WW2 days they had a standardized and regulated fuel stock, right? I enjoy reviewing the old photos and marveling at how simple and functional their...
Danilo, I'm happy for you. What is the temperature there where you are today and relative humidity ? I could swear you are cracking atospheric water vapor in...
Bruce... Love your description! Can I add this to it? Your comment below, I'll add, remember the steel in the gasifier, mainly the throat or reduction, these...
Danilo, I converted your mileage to be 0.355 pounds per mile or 2.82 miles per pound. My 91 olds (3.3L) will go 2 miles on a pound at 55 miles per hour in the...
Mike, My charcoall is of coffee feet i don´t know its density, I go weighs it to inform you, the temperature here this in 24 c and humidity 60%. you have to...
Hay OOE what a concept ! by golly I looked at the Recent photos and found them right off ! AMAZING ! ... I'm not a big fan of Yahoo but I am getting used to it...
Hi Steve, I caught up with your pictures tonight. Nice stuff but a couple of comments. My first suggestion would be to install a drain on your lid collection...
Danillo! Good to see you zooming fast down the road without any liquid fuel! I see the liquid fuel valve is shut off. The oil producing people can now pound...
If you live in Michigan, you can purchase a firewood gathering permit from the Department of Natural Resources. It costs about $20, or so. Obey the rules! The...
Thanks Andy, I work in a coffee farm and approximately of 5 in 5 years a pruning in the feet of coffees is made. the farm is big,1.000.000 of feet, then...
Are sure you did not mean 4x4x8 for a cord? Sent from my Verizon Wireless BlackBerry ... From: "glrf30" <glrf30@...> Date: Sat, 02 Jan 2010 02:38:28 To:...
