Hey Ron, Next time add some text to your message. I don't know whether to delete this as spam or not. Hope all's well. Maybe meet next time you get back...
44351
Ronald Hongsermeier
ronald.hongs...
Jun 23, 2012 4:12 pm
Sorry, Mike, was in a big hurry to get out of Dodge and was punished by my garage door frame. Prolly as punishment. I hope to see you next time round as well. ...
44352
Michael J
michaeldeanj...
Jun 24, 2012 9:56 pm
Hi, I am beyond impressed at the knowledge members of this group have about gasification. I started learning about the process a few months ago and have come...
44353
Stuart Perkins
stuartperkins
Jun 24, 2012 10:35 pm
I am unaware of tar problems with Wayne's designs. On Sun, 24 Jun 2012 14:30:33 -0000 ... --...
44354
David Siedschlag
pellets4fuel
Jun 24, 2012 11:56 pm
Mike, Hello, and welcome aboard. I would suggest also if you have not to join the Drive on wood site. Both this site and that one, as well as Jim Masons, ...
44355
Mike LaRosa
ook187
Jun 25, 2012 1:00 am
Duh ! 97 cavalier is running perfect .. Only OBD2 messages I got after 25 or so miles going around the block was an open injector circuit which of course is...
44356
logininn
Jun 25, 2012 2:27 am
Hey Mike, could you tell us again (without having to peruse back posts) what the engine size and vehicle weight is of that cavalier setup you have? Your pick...
44357
Mike LaRosa
ook187
Jun 25, 2012 3:12 am
2.2 liter .. 2" flex suction water pipe under the car. runs fine at 3500 to 4000 rpm (as Bruce and Sean French have noted on the ranger) .. Power is still...
44358
terry
grizbach88
Jun 25, 2012 4:01 am
Glad you got her running Mike. I see you have your signature butterfly controls. I could spot them anywhere. I tend to run about 8 to 10" doing about 60mph. ...
44359
Stuart Perkins
stuartperkins
Jun 25, 2012 12:33 pm
SWEM... On Mon, 25 Jun 2012 00:52:27 -0000 ... --...
44360
Mike LaRosa
ook187
Jun 25, 2012 2:03 pm
Hi Terry, About the most I can pull while sitting still and revving the engine is 4 or 5 inches but when pulling a hill it will pull 15 or 20. This is hard to...
44361
terry
grizbach88
Jun 25, 2012 4:10 pm
I live by my fuel mixture gauge coming off the O2 sensor. I highly recommend it for vehicles. I am curious how that brain affects timing from no code to...
44362
bates.rick
Jun 25, 2012 10:55 pm
Hi Terry, I remember reading that when the computer starts throwing codes it at least sometimes uses default settings for things like fuel mixture. I believe...
44363
Mike LaRosa
ook187
Jun 26, 2012 12:55 am
Hi Rick, I was hoping that Laren would make it to Indiana so he could not just meet more folks but so we could play some more music. I hope he is still alive....
44364
bates.rick
Jun 26, 2012 11:40 am
Hi Mike, More music would have been nice at Argos although with the hot sun and all the woodgas fun I was pretty beat by the time the sun went down. Hope you...
44365
terry
grizbach88
Jun 26, 2012 2:19 pm
Thanks Rick, I assumed that there was only one "limp in mode". I haven't even checked into what code it is throwing. I like to think it's saying "there's no...
44366
jim
jimmasonjim
Jun 26, 2012 5:45 pm
Bear Kaufmann, Jeff Tiedeken and I (Jim Mason) are at University of Minnesota, Morris this week installing the Powertainer and setting it up for its initial...
44367
arvid
tritowns
Jun 26, 2012 6:11 pm
Hey, still on my path to learning more... always learning :) Is there a mathematical relationship with area of nozzles to that of the restriction? Anyone know...
44368
Benjamin Bof
benjaminbof
Jun 26, 2012 6:28 pm
Really wonderful, I like it very much dreaming with 20´container to set my workshop. This week end I take contact with new president of Paraguay Federico...
44369
terry
grizbach88
Jun 26, 2012 9:38 pm
Arvid, That would be about 5% of the restriction.(surface area) Terry...
44370
logininn
Jun 27, 2012 12:50 am
Hey Terry, where did you get that 5% number? I have heard 7.75% and 8% but I don't know where that comes from either. Don M...
44371
anthonymeschke
Jun 27, 2012 3:26 am
Hi Jim, I think i sent you a personal message on Gek site but not sure. I would like to meet up this week. I am about 2.5 hrs away. I will not be able to...
44372
Larry Kueneman
l.kueneman
Jun 27, 2012 7:13 am
Ben, I am thrilled that you are taking the road of working with a governmental head toward this goal. Larry K Larry Kueneman Mountain Communities Fire Safe...
44373
terry
grizbach88
Jun 27, 2012 10:21 am
Don, I have seen it come up in a few places. FAO 720,Handbook of downdraft engine systems. Each gasifier design will be different depending on hearth...
44374
Roy H
raskolnik55
Jun 27, 2012 11:20 am
One solution to code problems. - http://www.uneedapart.com/used-ecus.php [Non-text portions of this message have been removed]...
44375
Stuart Perkins
stuartperkins
Jun 27, 2012 11:34 am
A $50 code reader can reset the codes too. I do that whenever my 2004 blazer throws a code...usually a 420...catalytic converter not working (not there). On...
44376
A. Olson
tritowns
Jun 27, 2012 1:36 pm
Thanks for the response... After I asked a started doing a bunch of math and came up with .055 or 5.5% average Nice to see that confirmed. ... From: logininn...
44377
Mike LaRosa
ook187
Jun 27, 2012 2:31 pm
I'm currently running at 0.064 with a 3.5 inch restriction and 8, 5/16" nozzles. Things seem happy. ML...
