Total of 680 mg. Download the Torrent first. You will need a Torrent downloader. I use Shareaza - free at http://www.shareaza.com/? id=download. There are...
8868
shiverin_sourdoughs
shiverin_sou...
Jul 1, 2007 11:09 pm
Duh, forgot to give the URL: http://sleekfreak.ath.cx:81/3wdev/CD3WD/INDEX.HTM Thanks, Bob ... Torrent ... English,...
8869
rpaydli
eenut2000
Jul 2, 2007 2:55 pm
Mike, what difficulties did you encounter when routing woodgas into the normally fuel injected oldsmobile? Do you have a fuel shut off to run solely on...
8870
Mike
ook187
Jul 2, 2007 6:37 pm
I'm still working with it. Tricking the computer is a major challenge on the 91 olds ! I have sucessfully overcome the computer previously with throttle body...
8871
Rob Windt
rob_windt
Jul 3, 2007 8:57 am
A cheap n nasty way is to put a switch in the fuel pump power wire, tho' it's preferable to turn the injectors off and keep fuel circulating past them Cheers ...
8872
Benjamin Bof
benjaminbof
Jul 3, 2007 12:36 pm
Mike, is possible to drill an 3/4 hole in manifold to produce vaccum for gasifier? In this case injection motors car run in "dual -fuel" lefting all devices,...
8873
Mike
ook187
Jul 3, 2007 1:17 pm
Rob & Benjamin, My ultimate plan is to cut near a 2" diameter hole in the intake manifold and plumb the gas in with a seperate woodgas carb but there will be...
8874
Benjamin Bof
benjaminbof
Jul 3, 2007 2:02 pm
Mike congratulations. We think this is the right way to modernizes woodgas devices. In 1989 we make an matter for Dinámica Rural revista showing an woodgas...
8875
borealbliss
Jul 3, 2007 3:05 pm
This might be a bit off topic, but I would like to try and identify the make and model of a wood stove from a picture only. Where would be the best place to...
8876
jim mason
jimmasonjim
Jul 3, 2007 5:31 pm
... mike, why did you decide against center feed in the end? did you go through all the schemes for center feed, but with holes pointing outward, or were you...
8877
Mike
ook187
Jul 3, 2007 8:51 pm
Jim and group, I tried straight down and tried different heights etc. I tried with a diverter underneath to spread the zone out and around to ensure a solid...
8878
jim mason
jimmasonjim
Jul 3, 2007 11:14 pm
mike, there might be several factors at work here. if i remember correctly, your reactor vessels are built out of tanks. single wall, no insulation. the...
8879
Mike
ook187
Jul 3, 2007 11:23 pm
Regarding my 91 olds, It turns out that almost all of the wiring diagrams I've looked at for my 91 olds are completely wrong. I still don't have a clue where...
8880
Mike
ook187
Jul 3, 2007 11:41 pm
Jim, My wife actually flew to San Fran shortly before I met her in 1986 to learn how to fire walk :o) .. Yep, she burned one of her feet .. It was healed...
8881
Tom Visel
five10man
Jul 4, 2007 2:23 am
Hey Mike, Just a thought or two on your car, from the perspective of an automotive tech: It would be interesting to see how the injector pulsewidth changes as ...
8882
Rob Windt
rob_windt
Jul 4, 2007 10:13 am
I get the occasional Asian import in for an LPG conversion and they drove me bats, no dealer backup, no wiring charts and no decent manuals available, cutting...
8883
Mike
ook187
Jul 4, 2007 12:56 pm
Hi Tom V, Thanks for the shop talk. The MAF is the only component that I'm concerned about so I'm not going to run it on woodgas till I have a few spares. I...
8884
Mike
ook187
Jul 4, 2007 1:06 pm
Rob, Thanks for the PCV mention. I hadn't even thought of that. My older cars either suck crankcase fumes into the intake or have a draft tube. There is no air...
8885
Rob Windt
rob_windt
Jul 4, 2007 1:18 pm
... No, every thing's on hold until the workshop is sorted and registered, gotta please the bureaucrats to make an honest living...
8886
Tom Visel
five10man
Jul 4, 2007 2:09 pm
Pretty much any GM FWD V6 that looks like yours (3.0/3.3/3.8) can swap MAF sensors, up 'til '96 or thereabouts. You might want to hit the junkyard to remove...
8887
shiverin_sourdoughs
shiverin_sou...
Jul 4, 2007 2:13 pm
Updated URL: http://www.cd3wd.com/CD3WD/ ---Now with 13 gigs. Must have been an earlier edition URL I gave the first time. Thanks, Bob...
8888
Mike
ook187
Jul 4, 2007 2:59 pm
Tom V, again, thanks for the details and for putting it out for the group. I have several types of flux remover and other items here that leave no residue. I...
8889
Mike
ook187
Jul 4, 2007 8:33 pm
Don't know where that spam stuff got in there but thought I'd run out a post to clear that out ??? .. Mike...
8890
Benjamin Domingo Bof
benjaminbof
Jul 4, 2007 9:22 pm
Dear group members. Really I´m belived about group capacity to modernizes gasifiers. All mails shows about it. Biofuels are on the spot. Brazil produces 15...
8891
Tom Visel
five10man
Jul 4, 2007 10:27 pm
Sorry 'bout the [SPAM] business - that was me not fighting with my comp's spam filters with sufficient diligence to let the important stuff through untagged. ...
8892
Mike
ook187
Jul 4, 2007 11:03 pm
The nail has been hit on the head .. The storm last night didn't knock down too many good branches for the cars .. The near rotten stuff laying on the ground...
8893
Mike
ook187
Jul 4, 2007 11:09 pm
Thanks Tom for the tech info .. People still think I'm nuts here when I tell them what I'm up to .. I'm headed back out to play with some more explosives .....
8894
shiverin_sourdoughs
shiverin_sou...
Jul 5, 2007 1:00 am
Which is why I like living in Alaska, unlimited, sustainable fuel. It may be -40 in the winter, but I can still keep warm and drive to town when I'm able or...
8895
Benjamin Domingo Bof
benjaminbof
Jul 5, 2007 1:13 pm
Bob, thanks for your answer. If you are in summer time can collect your fuel for the winter.Do you remeber the story of "Le Cigalle...". Colds are good for...
8896
shiverin_sourdoughs
shiverin_sou...
Jul 5, 2007 1:45 pm
Thank you Benjamin, That is very considerate of you. If you would like to send any plans you may have just send them offline to my email address. BTY, have you...
