I am looking for a larger vise for my LMS mill, I got the 3" and find myself running out of room? I know theres 4",5",6", but what would one recommend too...
A while back, I reported that I was getting a squealing sound when running the X2 mill at anything but low speed. It sounded like the bearings were worn out. ...
Hi You know o got that £6 tyre dept measure ment tool from Ebay Its the first photo in my album Well just had a few mins to have a mess with it today and look...
I am looking for carbide scribes and carbide automatic center punches?I have some carbide scribes -straight -,but looking for 90 degree ones, also I have...
Hi all Has anyone got or used these ELECTRONIC EDGE FINDER WITH LED AND BEEP I have just seen them and wondered how they compared with the manua wobbler type? ...
Hi All Well about my New a X1L which I got from ArcEuroTrade in the later part of last year. I have been using it over these last few months and apart from the...
Hi all, after 2 years I reach the limits of my X2. I'm looking for info on sieg X3 or SX3. For what I understand the structure is the same and the differences...
Does anyone know what size the brush retainer is for the stock X1 motor? Anyone know where I can buy them? My motor has been getting really hot lately so I...
G'day, My HM-10 mini-mill (re-badged X2) was purchased new about 6 or 7 months ago. During the initial clean and assembly stage I installed a LMS Belt...
Hi all, I made and installed a depth stop for my X3,( I know it only took me a year) the quill clamp is the usual split type and tightened with one 1/4-20...
I've just installed a used eBay-type Chinese DRO system (Rational WE6800-3) on my Grizzly G0619. It fired right up but after putting a dial indicator on the...
Brand new here, with a question that has probably been asked already, but did not see what I was after in a search. I have a Southbend 9A lathe (54" bed), and...
I pasted a link to the other group. it is for the mini mills but has a lot more users. I have the same mill- got it a month before you I think. love it. if u ...
looking into getting a rotary table for my x3. one of my current projects is a 2"x4" .693 thick 6061 that needs both of the 2" sides arced to match the part it...
Hi All, I amnew to this group I have just started and have an X3 which has been fine for a couple months, but its developed a problem of not starting every...
As the head on my SX3 is slightly out of square I tried to correct it by using the head swivel facility. undid the bolts as per instructions and then tried to...
How did the motor get wet? Long story. As an owner of an early machine I suffered the blue flash motor problem reported in earlier posts with two previous...
Hi All, I am an owner of an SX3 and have only recently found enough time to start carrying out the A.E.T strip & rebuild instructions. I noticed that since the...
I've just purchased a used DRO system for my G0619 and while waiting for it to arrive at my door I've located and downloaded the PDF user manual for the...
I want to purchase an ER32 collet set and chuck for my Grizzly G0619 SX3. Looking for comments and recommendations and maybe what to avoid. I'm leaning towards...
I've noticed that a few people suggested buying an ER32 collet on eBay from 800Watt. He/she apparently does not answer questions as I've asked tow and got no...
I'm thinking about purchasing an ER collet set for my SX3 mill. What are you folks using, ER32 or ER40? Looks like the ER32 goes to 3/4" and the ER40 goes to...
There has not been much development of fly cutters over the years and I thought others might be interested in this alternative approach. The flycutter uses a...
Has anyone mounted their SX3 by just using the rubber feet that they supply? I know that is not the best method but I cannot get under my bench top to put in...
