Just finished yesterday and running ever since on one nine volt battery. Not a bit of current needed, just a voltage presence is sufficient to draw in the ZPE...
Decided after 48 hours of running on the 9 volt to switch to a rechargeable 6 volt battery. After 2 days the speed has not dropped. www.geocities.com/mgmlab04...
... ron My stator mags are homemade. Four of them. They are made of # 22 guage wire with an average of 1150 wraps. My meter showed A resistance "in ohms"...
You connected the coils in parallel. If you want 80 ohms then connect them in series. ... <ronmathenyjr@y...> ... years ... inside ... rotor. ... thoughts or ...
Hi All, I am building an adams motor and woundered what experiences others have had, like what coil resistances where used how successful they have been are...
Hello everyone! I'm preparing to build an Adams type motor, which I intend to use as driving motor for Frenette's heater. And I have a bit of a problem, namely...
Hi Kreten, I am building an Adams motor as well at the moment. I don't think Peter L is up to date with where Robert is at so I will try to answer what...
Hello Russel, Thank you very much for your reply. I was going to give up on group cooperation (just kidding). Anyways, I totally agree with you, only as a...
I am in the final stages of making an Adams motor. I wish to constuct a 12 to 24 DC pulse coil that will be powerfull and efficient repelling a 7/16 inch...
Hi Tom, I certainly don't have all the answers but a bit more info might help. What is the core you are using for your coil? Is it pure iron or some less ...
Hi Russel, Thanks for the info. My magnets are 7/16 inch in diameter. So I will experiment using iron or grade 1010 soft steel 7/16 inch diameter rods and...
Hi All, Just new to this group, I have posted a couple of pictures in the Photo section. I am using an old hard drive as the spindle with four magnets epoxyed ...
For Tom (and whoeverelse), The optimum coil size starts with the dimension of the permanent magnet. The core CSA should be no more than 75% of the magnets CSA....
Hi All, Using eight magnets, I have managed to run on one 12volt battery and charge a second battery quicker than the first depletes. When the battery gets to...
... (power on ... Hi mgmlab04, I am working in the areas you are and have several questions to ask you about semiconducters and hall devices. I have a circuit...
Hi every one i got a question to ask of you. With utility bills getting higher and higher, i am trying to build an adams motor to run my whole house. Has any...
Hi Joel, I believe what you want to do can be done and has been done many times. I cannot give you all the answers because I have not done it yet but am ...
If I am able to build a small motor, would I be able to build a big one on the same principals that can sustain a house? Is there any one that would like to...
Hi Joel, Yes what you ask is possible but not straightforward as many have found out. Robert Adams did build big machines after building many small machines...
Notice to all Group Members, Wednesday the 10th of May Robert Adams died have recently suffered a serious stroke. His absence will be missed by many in the FE...
Hello Everyone! I was just reading the list till now but this sad event made me write. I think it will be welcome if someone among the members who was close...
Hi Tamas, The website I referred to was Roberts own site Aethmogen.com. If you haven't been there and it is still working read and download all that seems...
I would support by offering space on my servers for any website as well. (Just an offer of an alternative to the free services, more flexible this way) Judy...
Hi All group members, The Aethmogen website subscription has come up for renewal and as Robert Adams has died last May and is obviously not posting there any ...
In adamsmotor@yahoogroups.com, "elysilva2005" <elysilva2005@...> wrote: Have a good day to all! I wolud like how make a coil in photos. How many layers a have...
